Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
will be displayed on the monitor and only objects located less than 2
meters away can be seen.
The camera automatically changes to infrared mode when there is
insufficient light for normal vision.
When the camera is in this mode, the night vision icon (F) will be displayed
on screen.
Note: The light sensor (II) is located at the top of the camera. Take
care not to cover the sensor with any object to prevent the camera
from entering night mode when there is light in the room.
5.2.8. OUT OF RANGE WARNING
If the monitor is further away than allowed from the camera (check the
technical specifications), the image will be lost and the welcome screen
will be displayed on your monitor. The out of range symbol (A) and the
4 green volume LEDs (3) will flash in the top left corner of your screen for
one minute. By default, your monitor will activate the out of range sound
alert, emitting two double beeps every 3 seconds to warn you that the
two units are not communicating. The alarm will stop sounding after one
minute, or when you press any button, or when you bring the monitor close
to the camera and the connection is re-established.
If you want to cancel the sound alert , follow these steps:
1. Press the menu button (5) on the monitor to access the main menu.
2. Press the left (9) or right (7) navigation button until the wheel settings
icon is highlighted.
3. Press the down (8) navigation button until the alerts icon is highlighted.
4. Press the OK/ zoom button (10) and then press the OK/ zoom button
(10) again to activate or cancel the out of range sound alert.
If the alarm is red the sound alert is off, if it is green the sound alert is on.
Note: To get a better quality communication signal between the
monitor and the camera, use the monitor aerial (15) by simply pulling
it out. When the baby monitor is not in use we recommend you store
the aerial to prevent it from getting caught or breaking.
5.2.9. STANDBY MODE
With standby mode you can press the on / off button (1) directly to
switch off the screen and save power while you continue to listen to
sounds. To reactivate the image, simply press the on/ off button (1)
once again.
Note: In simultaneous view mode, if one of the cameras is not switched
on or is out of range, it cannot be in standby mode.
5.2.10. MAIN MENU
Press the menu (5) on your monitor to access the main menu.
5.2.10.1. CAMERA MENU
5.2.10.1.1. ADD CAMERA AND PAIRING
The pairing between the monitor and the camera will be done under two
circumstances:
- If you want to add an additional camera.
- If the monitor and the camera are not paired.
The monitor and the original camera leave the factory with channel
1 programmed, nonetheless, if for some reason, they are not,
you can link them manually following the steps indicated below.
To pair the camera and the monitor follow the next steps:
1. Press the menu button (5) to display the menu and show the highlighted
camera icon.
2. Press the down (8) navigation button until the add / remove icon is
displayed and press the OK / zoom button (10) to go into the sub-menu.
3. Press the up (6) or down (8) navigation button to select the camera
you want to add.
4. Press the OK / zoom button (10) to search for a camera unit.
5. Press the pairing button on the camera (IX) for 5 seconds.
6. Once paired the image of the camera will show immediately on the
monitor unit screen.
For various reasons you may lose the connection between the monitor
and a camera which is already connected. Should this be the case,
repeat the process explained above to connect the camera with the
monitor again.
Note 1: Before starting the pairing procedure, make sure the camera
and the monitor are close to one another and that the camera is
correctly plugged in or has sufficient battery and is switched on.
Note 2: Each camera can be linked just with one monitor at a time.
Nota 3: If the monitor and the camera, for some reason, have left the
factory without being paired, you will have to do it manually adding
the camera to channel 2. You won't be able to pair the camera again
with channel 1 until you have paired it in another channel and remove
the channel 1 camera.
5.2.10.1.2. DELETE CAMERA
To delete one of the cameras connected, follow the next steps:
1. Press the menu button (5) to display the menu and show the highlighted
camera icon.
2. Press the up (6) or down (8) navigation button until the add / remove
icon is displayed and then press the OK / zoom button (10) to go into
the sub-menu.
3. Press the up (6) or down (8) navigation button to select the camera
you want to remove and then press the OK / zoom button (10) again.
Note: A channel needs to be deleted before pairing to a new camera unit.
5.2.10.1.3. CHOOSING THE CAMERA
The device is designed to allow different areas to be monitored with up
to two cameras.
To select the camera you want to view, follow the steps described below:
1. Press the menu button (5) to display the menu and show the highlighted
camera icon.
2. Press the OK / zoom button (10) to go into the sub-menu.
3. Press the up (6) or down (8) navigation button to select the camera
you want to see (camera 1, camera 2).
4. Press the OK / zoom button (10) to go to the selected camera.
Note: The additional camera reference compatible with this baby
monitor is 89508 digital camera 4.3" pro.
5.2.10.1.4. SCAN MODE
This function automatically cycles through your paired camera channels
to display each camera for 12 seconds. This function can be used only
when you have more than 1 camera unit paired. To enter in this mode:
1. Press the menu button (5) to display the menu and show the highlighted
camera icon.
2. Press the OK / zoom button (10) to go into the sub-menu.
3. Press the up (6) or down (8) navigation button until the scan mode
icon is highlighted.
4. Press the OK zoom button (10).
5. The scan mode icon (C) will be displayed at the top of the screen to
indicate that it is activated.
Note 1: If one of the cameras is out of range, has no battery or is not
switched on, the monitor will warn you and the main screen will be
displayed during that period of time.
Note 2: To cancel scan mode, follow the same steps described above
and select from the options available: see camera 1, see camera 2, or
simultaneous view mode.
5.2.10.1.5. SIMULTANEOUS VISION MODE
This function will display the images from two cameras on screen at the
same time and can only be used when there is more than one camera
unit paired. If this is not the case, one part of the screen will show the
Miniland main screen.
1. Press the menu button (5) to display the menu and show the highlighted
camera icon.
2. Press the OK / zoom button (10) to go into the sub-menu.
3. Press the up (6) or down (8) navigation button until the simultaneous
view icon is highlighted.
4. Press the OK / zoom button (10).
5. The simultaneous viewing mode icon (D) will appear at the top of the
screen to indicate that it is activated.
Note 1: In simultaneous view mode you will not be able to use the two-
way function and you will only be able to listen to the camera selected.
Note 2: To select one camera or another use the right (7) or left (9)
navigation button, a green frame will be displayed around the image
of the camera selected.
5.2.10.2. VOX MODE
This mode allows you to control sound activation of your baby
monitor. If you activate VOX mode on the monitor and there is no
sound around the camera for 30 seconds, it will stop transmitting. The
14
Werbung
