Werbung
Verfügbare Sprachen
Verfügbare Sprachen
B. Camera selected and battery level indicator / camera charge
C. Scan mode
D. Simultaneous view mode
E. Nightlight
F. Night vision
G. Monitor volume
H. Vox Mode
I. Lullabies
J. Temperature
K. Time
L. Sound alert activated icon
M. Battery level / monitor charge indicator
N. Talk to the baby activated indicator
O. Zoom
4.2. CAMERA FUNCTIONS AND CONTROLS (FIGURE 2)
I. On / off button
II. Photo sensor
III. Camera lens
IV. Infra-red vision LEDs
V. Microphone
VI. Nightlight
VII. Speaker
VIII. Temperature sensor
IX. Pairing button
X. Charging LED
XI. USB-C power connector
5. INSTRUCTIONS FOR USE
5.1. BEFORE USE
5.1.1. PARENTAL UNIT POWER SUPPLY AND BATTERY USE
The monitor, or parent unit, is designed to be used with the battery or
with the AC/DC adapter supplied. Your baby monitor is supplied with a
rechargeable 3.7V 2000mAh Li-ion battery for the monitor.
By default, when the battery level has dropped too low, the volume LEDs
(3) and the low battery icon (M) will flash and the monitor will start to
emit a beep every five seconds.
To charge the monitor:
1. Connect the power supply adaptor to the USB-C socket (14). For safety
reasons, use only the adaptor supplied.
2. Connect the adaptor to the mains. The battery will be fully charged in
less than five hours.
While charging:
3. The charging LED (2) on the monitor will light up in red, and if the
unit is switched on the battery icon (M) on the screen will indicate that
the battery is charging.
4. When the battery is fully charged, the charging LED (2) will turn off.
5.1.2. BABY UNIT POWER SUPPLY AND BATTERY USE
The camera, or baby unit, of this baby monitor is designed to be used
with the battery or with the AC / CC adaptor supplied.
The camera in your baby monitor is powered by a rechargeable 3.7V – 950
mAh lithium ion battery.
By default, when the battery level has dropped too low, the volume LEDs
(3) and the low battery icon (B) will flash and the monitor will start to
emit a double beep every five seconds.
To charge the camera:
1. Connect the adaptor cable to the USB-C socket on the camera (XI).
Use only the adaptor supplied.
2. Connect the adaptor to the mains.
When charging:
3. When the battery is charging and if the unit is switched on, the LED
indicator (X) will flash for five seconds to indicate that the camera battery
is charging. While the camera is charging the LED indicator will remain
off and you can check the state of the battery on the monitor screen (B).
4. When the battery is fully charged, the camera charging indicator (B)
on the monitor will stop flashing.
Note: If the camera is switched off the LED indicator (X) will stay on
until the charging cycle has been completed.
WARNING: Choking hazard – Keep the cord out of the baby's reach.
NEVER place a camera with cables less than 1 meter from the cot.
Never use extension cords with AC adapters. Use only the AC adapters
supplied.
5.2. OPERATION
5.2.1. TURNING THE UNITS ON/OFF
5.2.1.1. MONITOR
To switch the monitor on, press the on/off button (1) for at least 4 seconds.
When the monitor has been switched on, the welcome screen will be
displayed.
To switch the monitor off, press the on/ off button (1) for at least 4 seconds.
If for some reason your monitor blocks, press and hold the power button
(1) until the unit turns off.
5.2.1.2. CAMERA
To turn the camera on or off, keep the power button (I) pressed in for
two seconds.
The nightlight (VI) will come on for two seconds when the unit is switched
on and flash twice when the unit is switched off.
When you have installed the camera and turned it on, you can see the images
and listen to the sounds captured in your baby's room via the monitor.
5.2.2. MONITOR VOLUME
Press the OK / zoom button (10) and the up (6) or down (8) navigation
button to show the volume bar. Then, press the up (6) or down (8)
navigation button to select the desired volume, from 0 (mute) to 6 (very
loud). The default volume setting is 3.
To exit this function, you can do the following:
1. Press the menu button (5) or the OK / zoom button (10).
2. Do not touch the monitor for 15 seconds.
Note: The volume icon (G) will appear at the top of the screen along
with a number indicating the volume level.
5.2.3. MONITOR BRIGHTNESS
Press the OK / zoom button (10) to show the brightness bar. Then,
press the left (9) or right (7) navigation button to select the desired
brightness, from 1 through to 7. The default brightness setting is 4.
To exit this function, you can do the following:
1. Press the menu button (5) or the OK / zoom button (10).
2. Do not touch the monitor for 15 seconds.
5.2.4. PAN & TILT
This camera can be angled from the monitor by pressing the left (9),
right (7), up (6) or down (8) navigation button until you find the
desired viewpoint. Do not try to move the camera or the lens manually.
The camera has 355º lateral vision and 53º vertical vision. It is important
not to force the motor when it reaches the maximum vision in one
direction.
5.2.5. TALKING TO THE BABY
You can talk to your baby from the parents' unit (for example, to calm them
down and so they understand you're on your way) or to your partner (if
he or she is in the baby's room).
Press the button to talk to the baby (12), keep it pressed down and speak
into the front of the monitor. While this function is in use, a microphone
icon (N) will be visible at the bottom of the LCD screen. Release the
button when you have finished speaking to listen to sounds coming from
the baby's room.
Bear in mind you won't be able to hear your baby while you're talking to
them. To listen again, release the button (12).
5.2.6. DIGITAL ZOOM
If you wish, you can increase the size of the image viewed by using the
zoom function.
Keep the OK / zoom button (10) pressed for two seconds to access
this function.
When in this mode, you can continue to move the image with the monitor
navigation buttons (up (6), down (8), right (7) or left (9)).
A zoom icon (O) will be displayed at the bottom of the LCD screen.
To exit the zoom function, keep the OK / zoom button (10) pressed for
at least 2 seconds.
5.2.7. INFRARED NIGHT VISION (AUTOMATIC)
The infrared night vision function allows the camera to pick up images in
dark or low light conditions. In this mode, only black and white images
13
ENGLISH
Werbung
