Bosch Relyy'y BGS31800 Gebrauchsanweisung Seite 39

19*
Fig.
a) Telescopic tube without accessory connection:
To release the connection, turn the handle slightly
and pull it out of the telescopic tool.
b) Telescopic tube with accessory connection:
To release the connection, press the locking collar
on the telescopic tube and and pull out the handle.
20*
Fig.
a) Nozzle without accessory connection:
To release the connection, turn the telescopic tube
slightly and pull it out of the loor nozzle.
b) Nozzle with accessory connection:
To release the connection, press the locking collar
and pull the telescopic tube out of the loor nozzle.
Cleaning and care
Emptying the dust separation system
21
Fig.
In order to achieve the best possible vacuuming re-
sults, the dust container should be emptied after every
use or, at the latest, when dust in the dust container
has reached the marking at any point.
!
Caution
The dust container can only be removed when the
appliance is in a horizontal position. Therefore,
place the appliance on the loor to unlock the re-
lease button.
22
Fig.
a) Press the release button and pull the dust container
out of the appliance using the handle.
b) Remove the lid from the dust container and empty
the dust container.
c) Put the lid back on the dust container.
d) Remove any dirt which may have been lodged under-
neath the container ejector opening.
e) Insert the dust container in the appliance, so that it
'clicks' audibly into place.
Maintaining the dust-collection system
In normal operation
If there is a substantial decrease in cleaning perfor-
mance, you should clean the foam ilter.
Cleaning the foam ilter
Switch off the appliance.
23
Fig.
a) Open the lid of the foam ilter by pulling on the lo-
cking lever.
b) Remove the ilter cartridge with foam ilter using the
tab.
Remove the foam ilter from the ilter cartridge and
tap out both parts.
38
c) If they are very dirty, the foam ilter and ilter cart-
ridge should be cleaned under running water.
Alternatively, the unit can be cleaned in the
washing machine at max. 30 °C using a gentle pro-
gramme and the lowest spin speed.
TIP: To protect other laundry items, put the ilter
unit into a laundry bag.
d) Allow the foam ilter and ilter cartridge to dry com-
pletely (at least 24 hours) and then reinsert the foam
ilter into the ilter cartridge.
e) Insert the ilter cartridge with foam ilter back into
the appliance. Close the lid of the foam ilter.
!
Caution
The lid will only close if a ilter has been inserted.
In the event of a fault
After cleaning the foam ilter, the cleaning performance
is still unsatisfactory:
Removing a blockage from the dust separation
24
Fig.
Switch off the appliance.
a) Hold the appliance lid by the recessed handle and
open it.
b) Unlock the cover by turning it anti-clockwise, and
remove it from the appliance.
= Remove the blockage from the collecting unit. >
c) Put the cover back on and lock it in place by turning
it clockwise.
= Close the appliance lid. >
If, after inspecting the collecting unit, the suction is
still unsatisfactory despite the unit being free from
blockages, check whether the nozzle, suction pipe or
lexible hose are blocked. This can also cause a loss
of suction.
Exhaust ilter care
Depending on the model, your appliance is equipped
with either a HEPA ilter
Depending on the model, your appliance has additional
sound insulation behind the HEPA or micro ilter. This
does not have to be cleaned.
HEPA ilter
You can determine with which HEPA ilter your appli-
ance is equipped by looking at the imprint on the ilter
frame next to the reference number:
"washable" – the ilter can be washed.
No additional imprint – the ilter must be replaced.
Cleaning a washable HEPA ilter
The HEPA ilter with the "washable" imprint is designed
so that it does not need to be replaced, provided the
appliance is used as intended in the household.
To ensure that the vacuum cleaner is working at its op-
timum power level, the exhaust ilter should be rinsed
out after one year. The iltering action of the ilter re-
mains intact, even if the ilter surface becomes disco-
loured.
* Dependent on model
or a micro ilter
25
Fig.
.
27
Fig.