Makita LW1400 Betriebsanleitung Seite 6

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Wheel diameter
Max. wheel thickness
Hole diameter
No load speed
Dimensions
(L x W x H)
Net weight
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014
• The shape and weight vary depending on the specifications which differ country to country.
Intended use
The tool is intended for cutting in ferrous materials with
appropriate abrasive cut-off wheel. Follow all laws and
regulations regarding dust and work area health and
safety in your country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
For public low-voltage distribution
systems of between 220 V and 250 V
Switching operations of electric apparatus cause volt-
age fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.18 Ohms it can be pre-
sumed that there will be no negative effects. The mains
socket used for this device must be protected with a
fuse or protective circuit breaker having slow tripping
characteristics.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-3-10:
Model LW1400
Sound pressure level (L
Sound power level (L ) : 110 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model LW1401
Sound pressure level (L
Sound power level (L ) : 110 dB (A)
WA
Uncertainty (K) : 3 dB(A)
With European type safety guard
With safety guard other than
European type
With European type safety
guard and under cover
) : 102 dB(A)
pA
) : 102 dB(A)
pA
LW1400
530 mm x 295 mm x 640 mm
530 mm x 295 mm x 640 mm
18.7 kg
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-3-10:
Model LW1400
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model LW1401
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
6 ENGLISH
LW1401
355 mm
3 mm
25.4 mm
-1
3,800 min
500 mm x 295 mm x 640 mm
500 mm x 290 mm x 620 mm
18.3 kg
/II
2
) : 2.5 m/s or less
h
2
2
) : 2.5 m/s or less
h
2