Makita DCC501ZX1 Betriebsanleitung Seite 16

Removing and installing diamond
wheel
CAUTION:
Use only the Makita hex wrench
supplied to remove and install a diamond wheel.
CAUTION:
When installing a diamond wheel,
be sure to tighten the bolt securely.
CAUTION:
Always install a diamond wheel so
that the arrows on the diamond wheel point in the
same direction as the arrows on the wheel cover
and gear housing. Otherwise the wheel rotates in
reverse, it may cause personal injury.
To remove the diamond wheel, press the shaft lock
fully so that the diamond wheel cannot revolve and use
the hex wrench to loosen the hex bolt clockwise. Then
remove the hex bolt, outer flange and diamond wheel.
► Fig.11: 1. Shaft lock 2. Hex wrench 3. Hex bolt
4. Loosen 5. Tighten
NOTICE:
If the inner flange is removed, install it on
the spindle with its wheel mounting part facing the
diamond wheel.
To install a diamond wheel, follow the removal pro-
cedure in reverse. Make sure the diamond wheel is
installed so that the arrows on the wheel point in the
same direction as the arrows on the wheel cover and
gear housing.
BE SURE TO TIGHTEN THE HEX BOLT SECURELY.
► Fig.12: 1. Hex bolt 2. Outer flange 3. Diamond
wheel 4. Inner flange 5. Cup washer
6. Arrow
Water supply tank
CAUTION:
When filling the tank with water, be
careful not to spill water over the tool.
CAUTION:
Be sure that the water supply lever
on the wheel cover is set in the "OFF" (O) position
before installing the water supply tank.
Installing water supply tank
Insert the tank with the water supply cap pointing down-
wards into the water supply holder until it locks with a
click.
► Fig.13: 1. Water supply cap 2. Water supply holder
Removing water supply tank
Press the eject button to release the tank, and then pull
the tank off.
► Fig.14: 1. Eject button
NOTICE:
Be careful not to hold the water-filled tank
upright (with its lid-cap facing downwards) as water
drops may leak out of the vent pin hole.
► Fig.15: 1. Lid-cap 2. Vent pin hole
Water supply hose
CAUTION:
Be sure that the water supply lever
on the wheel cover is set in the "OFF" (O) position
before turning the water on.
Connecting to the mains water
supply
NOTE: The type of water outlet may vary depending
on your region of residence. Use an appropriate
faucet adapter or tap connector to attach the hose to
the mains water supply as necessary.
1.
Connect the water supply plug to the supply water
outlet.
► Fig.16: 1. Supply water outlet 2. Water supply plug
2. Unscrew the water supply cap attached to the
water supply tank.
► Fig.17: 1. Water supply cap 2. Water outlet
NOTICE:
Be careful not to lose the rubber washer
placed at the bottom of the water supply cap when-
ever you reassemble the cap.
3. Attach the water supply cap onto the cap plug of
the hose.
► Fig.18: 1. Water supply cap 2. Cap plug
4. Insert the hose with the water supply cap pointing
downwards into the water supply holder until it locks
with a click.
► Fig.19: 1. Water supply cap 2. Water supply holder
Disconnecting from the mains water
supply
1. Set the water supply lever on the wheel cover in
the "OFF" (O) position and turn the water off.
2.
Press the eject button to release the water supply
hose, and then pull the hose off.
► Fig.20: 1. Eject button
3. Remove the water supply plug from the supply
water outlet.
Installing dust cover
Optional accessory
CAUTION:
When installing an optional wheel
cover, be sure to tighten the screw securely.
Removing standard-equipped wheel
cover
Remove all the attachments on the pre-installed wheel
cover before replacing it with an optional cover.
Loosen the screw and pull the cover apart from the gear
housing.
► Fig.21: 1. Screw
16 ENGLISH