After Use - Makita HW001G Betriebsanleitung

3. Connect the high pressure washer and the faucet
using a water hose. After that, open the faucet.
► Fig.21
NOTICE:
Before turning on the machine, make
sure that the faucet is fully open.
4.
Select the desired mode by pressing the mode
switching button, and then turn the power switch clock-
wise to turn on the machine.
► Fig.22: 1. Power switch 2. Mode switching button
5. To eject a water jet, unlock the stopper and squeeze
the trigger. Once water is ejected stably from the trigger
gun, release the trigger and turn the machine off.
► Fig.23: 1. Stopper
NOTE: Be sure to remove the nozzle from the trigger
gun before performing this operation.
6. Attach the nozzle to the trigger gun for your purpose,
and then turn on the machine to start the washing operation.
When you suspend the operation, you can temporarily
place the trigger gun as shown in the figure.
► Fig.24
Supplying water from a tank/reservoir
CAUTION:
When attaching the sleeve to the
filter case of the strainer assembly, be careful not
to hurt your hand by the hose band.
NOTICE:
Always use Makita's hose assembly
and strainer assembly.
NOTICE:
Always keep 1.0 m or less in height
between the inlet of the high pressure washer and
the water surface. Otherwise, the high pressure washer
will be unable to take the water up into the pump.
NOTICE:
The water level that the machine can
pump up is 100 mm or more.
NOTICE:
Do not use water from rivers, ponds,
or water mixed with sand or mud. Doing so may
cause malfunction.
NOTE: If it takes a long time for the water to come
out, clean the strainer and the filter of the strainer
assembly.
You can supply water from a tank or reservoir instead of a faucet.
1. Turn off the machine, and remove the nozzle from
the trigger gun.
2. Connect the hose assembly and strainer assembly
to the water hose connector.
► Fig.25: 1. Tank/reservoir 2. Strainer assembly
3. Hose assembly 4. Water hose connector
3. Turn on the machine, and unlock the stopper and
squeeze the trigger. Once water is ejected stably from
the trigger gun, release the trigger.
► Fig.26: 1. Trigger gun
NOTE: It takes about 10 to 60 seconds for the water
to come out.
NOTE: Be sure to remove the nozzle from the trigger
gun before performing this operation.
4. Turn off the machine and attach the nozzle to
the trigger gun for your purpose, and then turn on the
machine to start the washing operation.
NOTE: When water is not ejected, detach the hose
assembly and strainer assembly and soak them in
water. Then reconnect them to the machine.
► Fig.27: 1. Hose assembly and strainer assembly
NOTE: If water suction does not work, it takes a long
time, or the water pressure is not enough, check the
following:
• Loosening of the hose assembly, strainer
assembly, and water hose connector.
• Coupling sleeves of the hose assembly are
firmly attached onto the water hose connector
and filter case of the strainer assembly.
Tighten if they are loose.
Hose assembly
► Fig.28: 1. Coupling sleeve
Strainer assembly
► Fig.29: 1. Hose band 2. Filter case
Water hose connector
► Fig.30: 1. Water hose connector

After use

CAUTION:
After operating the high pressure
washer, always perform the procedure described
in this manual. Residual pressure in the trigger gun
or high pressure washer can cause personal injury or
damage to the pump inside.
1. Turn off the machine, and remove the nozzle from
the trigger gun.
2. Close the faucet and disconnect the water hose
from the high pressure washer.
► Fig.31
3.
Switch on the high pressure washer again.
4. Squeeze the trigger until the remaining water in
the high pressure washer is discharged.
► Fig.32
NOTICE:
Do not run the motor for longer than 1
minute.
5. Switch off the high pressure washer and remove
the battery cartridges.
► Fig.33: 1. Battery cartridge
6.
Disconnect the high-pressure hose from the trig-
ger gun and the high pressure washer.
► Fig.34: 1. Trigger gun 2. High-pressure hose
NOTICE:
To prevent the high-pressure hose from
being damaged, drain the remaining water in the
hose before storing.
7. Hold the machine with both hands, and drain the
remaining water inside of the machine by tilting the
machine as shown in the figure.
► Fig.35
22 ENGLISH