XZENT X-F275 Benutzerhandbuch Seite 5

MODE 1, FIAT DUCATO III X290 AS OF 2014
1
A1
7
5
A
Operation buttons:
1. MUTE: press to mute or unmute all audio.
2. Vol+: press to increase active audio volume level. For example, press while Navigation Voice
is speaking to increase the volume level of Navigation voice, the ducked or muted media
audio stays unchanged.
3. Vol-: press to decrease active audio volume level. For example, press while Navigation Voice
is speaking to decrease the volume level of Navigation voice, the ducked or muted media
audio stays unchanged.
4. CAM/voice: press to activate CAM source. Press again to close CAM source. Press & hold to activate
CarPlay voice control.
5. Pickup: press during incoming call to pick up the call.
6. Skip next: this button follows the Graphical User Interface (GUI) function of the active audio source
7. Skip last: this button follows the Graphical User Interface (GUI) function of the active audio source.
8. Hangup: press during active call to end the call.
A: You can customize the buttons of your SWC to your preference by placing standard or alternative
buttons to your SWC. The process is explained at the end of this chapter.
Alternative buttons:
A1. Alternative function SRC/Voice: Press to select a different Source via Main Menu highlighting.
A2. Alternative function FAV: Press to invoke the assigned FAV function from Setup.
B: This button will reset any custom confi guration on the SWC back to factory settings.
8
2
3
4
A2
6
8
B
SWC (re)Assignment process:
The process is similar to both SWC modes and only differs by other standard and alternative buttons.
The standard and alternative buttons function are explained at the beginning of this chapter for each
mode. In case of using the existing mini-ISO connector at your compatible vehicle – you can re-assign
the buttons of your SWC. Please note that this mode is NOT for the IR-stalk interface mode. Press the
"Change" button to start re-assiging the functions to your liking. The system will clear all buttons from the
steering wheel and marks the top left SWC button which shall be assigned fi rst. You need to assign all
cleared buttons one by one from top left to bottom and then the right side from top to bottom. The current
button which is to be assigned with a function will be hi-lighted for you. Example: To assign a function,
select a function icon via touch from the middle (for example SRC / voice). After the desired function (in
this example SRC / voice) is marked, press the corresponding SWC-Button (in this example top left).
The system will now gray-out the SRC / voice button in the middle and put the SRC / voice function to
the top left SWC button. Later you can trigger SRC / voice by pressing the top left SWC icon (instead of
default MUTE). After the fi rst button is assigned, the system will hi-light the next button to be assigned by
a still available (non-grayed-out) function from the middle. After all buttons on the SWC are defi ned – you
can close the SWC assignment and use the new confi guration from now on. To restore back to default
values press the "Default" button. The functions will then restore to standard values.
Board/Trip-Computer:
The SWC buttons for trip-, board computer and cruise control operation are directly assigned to the rela-
ted vehicle functions, e.g. the function of these buttons on the steering wheel is completely independent
of the device mounted in the vehicle.
Note:
The SWC related functions are only available if the device is connected with a compatible stalk-interface
via IR in wire to a compatible vehicle model or via mini-ISO (Analog Key) if existing in the vehicle.
With the Ducato Series 8, only the buttons on the back of the steering wheel are connected via a red
mini ISO, as the buttons visible in the front are connected via CAN / LIN.
CAN IR stalk interface modules are being developed by various providers and, as soon as these are
available, details on support can follow.
The change from mode 1 to mode 2 must be completed by restarting the device.
9