Inhaltsverzeichnis
Werbung
TROUBLESHOOTING
In case your dishwasher doesn't work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS
POSSIBLE CAUSES
Salt reservoir is empty (after refill the salt indica-
Salt
indicator is lit
tor may remain lit for several wash cycles).
Rinse aid dispenser is empty (after refill the
Rinse aid
rinse aid indicator may remain lit for several
indicator is lit
wash cycles).
The appliance has not been plugged in
The dishwasher
properly.
won't start or does
not respond to
Power outage.
commands.
The dishwasher door is not closed.
Auto Door pin is not pulled in.
Cycle is interupted by door opening for > 4 sec. Close the door and press START/Pause.
It does not respond to commands. Display
shows: F9 or F12 and both On/Off
and START/Pause LEDs are blinking rapidly.
The dishwasher
The wash cycle has not finished yet.
won't drain.
Display shows: F3
The drain hose is bent.
and both On/Off
and START/Pause
The sink drain pipe is blocked.
LEDs are blinking
rapidly.
The filter is clogged up with food residues.
The dishwasher
The dishes are rattling against each other.
makes
excessive noise.
An excessive amount of foam has been pro-
duced.
The crockery has not been arranged properly. Arrange the crockery correctly
The dishes are not
clean.
The spray arms cannot rotate freely, being
hindered by the dishes.
The wash cycle is too gentle.
An excessive amount of foam has been pro-
duced.
The cap on the rinse aid compartment has
not been shut correctly.
The filter is soiled or clogged.
There is no salt.
The dishwasher
No water in the water supply or the tap is
does not fill the
closed.
water. Display
and F6,
shows:
The inlet hose is bent.
both On/Off and
START/Pause LEDs
The sieve in the water inlet hose is clogged; it
are blinking rapidly.
is necessary to clean it.
Dishwasher finishes
Drain hose positioned too low or siphoning
the cycle prematurely.
into home sewage system.
Display shows: F15
and both On/Off
and START/Pause
LEDs are blinking
Air in water supply.
rapidly.
Policies, standard documentation, ordering of spare parts and additional product
information can be found by:
•
Visiting our website docs.indesit.eu and parts-selfservice.whirlpool.com
•
Using QR Code
•
Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product's
identification plate.
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry
at https://eprel.ec.europa.eu.
8
SOLUTIONS
Refill reservoir with salt (for more information - see page 2).
Adjust water hardness (see table, page 2).
Refill dispenser with rinse aid (for more information - see page 2).
Insert the plug into the socket.
For safety reasons, dishwasher will not restart automatically when power
returns. Press the START/Pause button to resume the cycle.
Vigorously push the door until you hear the "click".
Switch off the appliance by pressing the ON/OFF button, switch it back on
after approximately one minute and restart the program. If problem persists,
unplug the appliance for 1 minute, then plug it back in.
Wait until the wash cycle finishes.
Check that the drain hose is not bent
Clean the sink drain pipe.
Clean the filter
(see CLEANING THE FILTER ASSEMBLY)
Position the crockery correctly
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers
(see FILLING THE DETERGENT DISPENSER)
by pressing the DRAIN button
program without detergent.
Arrange the crockery correctly
Select an appropriate wash cycle
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers
(see FILLING THE DETERGENT DISPENSER)
Make sure the cap of the rinse aid dispenser is closed.
Clean the filter assembly
(see CARE AND MAINTENANCE)
Fill the salt reservoir
(see FILLING THE SALT RESERVOIR)
Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the
dishwasher and reboot.
After having carried out the verification and cleaning, turn off and turn on
the dishwasher and restart a new program.
Check if end of drain hose is placed at correct height (see INSTALLATION).
Check for siphoning into home sewage system, install air admittance valve
if necessary.
Check water supply for leaks or other issues letting air inside.
(see INSTALATION INSTRUCTION)
.
.
(see LOADING THE RACKS)
. Restart dishwasher
and run new
(see OPTIONS AND FUNCTIONS)
.
(see LOADING THE RACKS)
.
(see LOADING THE RACKS)
.
(see PROGRAMS TABLE)
.
.
.
:
400011670860
03/2023 ks - Xerox Fabriano
.
IEC 436
Werbung
Inhaltsverzeichnis
