Safety Instructions For Machines With Combustion Engine - Zipper Maschinen ZI-BHS2600 Betriebsanleitung

When working close to the ground, ensure that no sand, gravel or stones get entangled be-
•
tween the blades.
Do not touch the ground with the tip of the blade bar.
•
First cut the hedge laterally then on top.
•
Especially with larger hedges, you should not work hastily but carefully until all branches are
•
neatly cut back.
Clear away branches, scrub and cutting material fallen on the ground.
•
Do not operate the machine with damaged or worn blades.
•
In case of emergency, immediately switch off the machine by setting the ON-OFF switch to
•
position "0" (Off).
Never try to remove objects stuck in the blade bar when the engine is running.
•
• If the blade bar strikes a foreign object or a solid object gets jammed in the blades, or if the
machine generates unusual noises or starts to vibrate, switch off the machine and wait until it
has come to a standstill. Then remove the spark plug connector. Only then can the machine be
inspected for possible defects.
• Never use a rusted blade bar. This may cause serious injuries when operating the machine.
In order to reduce the risk of injuries, take regular breaks to avoid fatigue and exhaustion.
•
In case of nausea, headaches, visual disturbances (e.g. reduced visual field), hearing problems,
•
dizziness, loss of concentration, the machine must not be operated. These symptoms can be
caused by an over-concentration of exhaust fumes in the working area.
Kickback:
• Kickback is a sudden reaction of the machine when the blade bar hits a solid object or when the
blade bar is blocked. This results in a sudden, uncontrolled movement of the machine.
• Kickback can be avoided by observing the following precautions:
When operating the machine, be careful not to get in contact with any objects that could
o
damage the blade bar.
o Always hold the machine by the handles with both hands and ensure a secure footing so
that you can withstand sudden kickback forces.
Always keep your hands away from the blade bar while operating the machine. There is a
o
risk of injury in case of kickback.
11.5

Safety instructions for machines with combustion engine

Do not touch the gearbox during operation or immediately after stopping the machine! These
•
engine parts become hot and can cause burns.
To reduce fire hazard, keep the engine and muffler free of debris, leaves and excess lubricant.
•
Only operate the machine outdoors (danger from carbon monoxide!). Exhaust fumes contain
•
odourless and colourless carbon monoxide. An exposure can cause unconsciousness and can
lead to death.
• Do not smoke while operating the machine.
CAUTION: Fuel is highly flammable and its vapours represent a potential hazard of explosion!
•
Smoking, open flames and the operation of spark-generating electrical equipment (e.g.: weld-
•
ing equipment or grinding machines) are prohibited during refuelling.
Only refuel the machine in well-lit and ventilated areas, never indoors.
•
Do not open the fuel filler cap while the machine is running.
•
Do not refuel the machine when the engine is running or the engine is still hot.
•
Let the engine cool down for about two minutes before refuelling.
•
Make sure the fuel does not overflow. If fuel has spilled during the refuelling process, do not
•
attempt to start the machine. Instead, remove the machine from the contaminated area.
Close the fuel filler cap again after refuelling.
•
• Ensure that no fuel leaks from the rear outlet tube.
• Do not use petrol or other types of fuel or flammable solutions to clean the machine. Fuels and
solutions can ignite or explode.
Always drain the fuel tank outdoors.
•
• Store fuel only in designated and approved containers.
• Let the machine cool down before storage.
• Never store the machine or the fuel container close to open flames.
ZIPPER MASCHINEN GmbH www.zipper-maschinen.at
SAFETY
23
ZI-BHS2600