Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
GB
GB
GB
GB
GB
8 8 8 8 8
Quartz glass tube
14
14
14
14
14
Insert the emitter (9 9 9 9 9 ) carefully and connect with the plug (10
blue protective cap (11
Attach the blue protective cap (11
Caution! For safety reasons, the UV emitters may only be started in
Caution! For safety reasons, the UV emitters may only be started in
Caution! For safety reasons, the UV emitters may only be started in
Caution! For safety reasons, the UV emitters may only be started in
Caution! For safety reasons, the UV emitters may only be started in
the unit when the blue protective cap (11) is mounted.
the unit when the blue protective cap (11) is mounted.
the unit when the blue protective cap (11) is mounted.
the unit when the blue protective cap (11) is mounted.
the unit when the blue protective cap (11) is mounted.
11
11
11
11
11
Star
Startup
Star
tup
tup
tup
Star
Star
tup
Open the water supply line.
Open the water supply line.
7 7 7 7 7
Open the water supply line.
Open the water supply line.
Open the water supply line.
See UV-Control II installation and operating instructions for the remain-
ing startup procedure.
6 6 6 6 6
Operation/maintenance
Operation/maintenance
Operation/maintenance
Operation/maintenance
Operation/maintenance
10
10
10
10
10
All machinery requires regular maintenance. Maintenance work should
always be carried out by a specialist, who should also replace those
parts that are liable to wear out. We recommend that you enter into a
service agreement.
5 5 5 5 5
Important note for control cabinet installation (UV-Control in ventilated
control cabinet):
9 9 9 9 9
Caution: fire hazard!
Caution: fire hazard!
Caution: fire hazard!
Caution: fire hazard!
Caution: fire hazard!
Soiled air filters can lead to overheating and destruction of the switching
cabinet.
The condition of the air filters must be checked every 2 months on units with
ventilated switching cabinets. The air filter must be replaced when soiling is
clearly visible, or after 6 months at the latest.
Cleaning the unit
Cleaning the unit
Cleaning the unit
Cleaning the unit
Cleaning the unit
The quartz glass tube should be cleaned each time an emitter is changed.
Remove mains plug. Close the shut-off valves. Drain the unit.
Loosen the 2 screws of the blue protective cap (11
tective cap and pull the plug (10
Remove the UVC emitter (9 9 9 9 9 ).
O-ring
Unscrew the tensioning screw (7 7 7 7 7 ) with the support ring (8 8 8 8 8 ).
Remove the quartz glass tube (5 5 5 5 5 ).
Clean the quartz glass tube with a soft cloth. If required, an acid (e.g.
citric acid) or a solvent (e.g. alcohol) can be used.
Push the O-ring (6 6 6 6 6 ) approx. 40mm over the top of the quartz glass tube
(5 5 5 5 5 ) and insert the quartz glass tube (5 5 5 5 5 ) again carefully (follow the lower
guide in the radiation chamber).
Tighten the tensioning screw (7 7 7 7 7 ) and support ring (8 8 8 8 8 ) hand-tight and
tighten further using the special spanner from the bag of accessories if
necessary (a small gap remains between the tensioning screw and the
cover of the UV unit).
Insert the emitter (9 9 9 9 9 ) carefully and connect with the plug (10
protective cap (11
Attach the blue protective cap (11
Open the shut-off valves up- and downstream of the unit.
The unit is now ready for use.
Sanitization of the UV unit
Sanitization of the UV unit
Sanitization of the UV unit
Sanitization of the UV unit
Sanitization of the UV unit
Steaming of the unit in forbidden.
Sanitization can be done with hot water (max. 85 °C), for max. 1 hour.
For this process, the lamp connection cable has to be removed from the
lamp, and the UV sensor dismounted out of the measuring window.
(Caution
Caution! Danger of burst).
Caution
Caution
Caution
Page 14 of 48
11). Ensure that the plug is inser
11
11
11
Ensure that the plug is inser
Ensure that the plug is inser
Ensure that the plug is inserted proper
Ensure that the plug is inser
11) and secure it with 2 stud screws.
11
11
11
10
10
10) from the UV emitter.
10
11
11
Ensure that the plug is inser
Ensure that the plug is inser
11
11). Ensure that the plug is inser
Ensure that the plug is inser
Ensure that the plug is inserted proper
11) and secure it with 2 stud screws.
11
11
11
10
10
10) of the
10
ted proper
ted proper
ted proper
ted properly ly ly ly ly.
11
11
11). Remove the pro-
11
10) of the blue
10
10
10
ted proper
ted proper
ted properly ly ly ly ly.
ted proper
Werbung
Inhaltsverzeichnis
