Care And Maintenance - Peavey PVXp 15 Bedienungsanleitung

Check to make sure light dimmers are not on the same circuit as the PVXp 15, the mixer or any source devices.
™
If light dimmers are used, then it may be necessary to turn them fully ON or fully OFF to eliminate or reduce
hum. This is a typical AC wiring/light dimmer interference problem, not a design flaw of the PVXp 15.
The third wire (ground plug) on the AC plug should NEVER be removed or broken off, as this is a potential safety
hazard.
Distorted or Fuzzy Sound
First, ensure the mixer (signal source) is not clipping or being overdriven. Make sure the Level (6) control on the
PVXp 15 has not been set too low. Check that the input plug is fully seated in the input jack on the rear panel of
the PVXp 15. Ensure that a power amp has not been plugged into the input jack of the PVXp 15. If an extension
cord is being used to provide the AC power to the unit, ensure that it is of sufficient current capacity and that it
is not also being used to supply power to any other device.
The PVXp 15 has a built-in Contour EQ button to extend and smooth the natural response of the speakers in the
system. When the Contour button is engaged, some Bass boost and HF EQ have been applied and the system
then has a nominally balanced response for background music, so it should require little, if any, additional
EQ. If excessive additional bass boost or HF boost have been added externally to the PVXp 15, it could cause
premature overload at high SPL. Reduce the amount of any external (mixer, rack) EQ and see if that clears up
the distortion.
Check to make sure that a line level signal is not being input through the XLR jack, this has 13 dB more gain
than the 1/4" TRS jack, and could be overloading with high mixer output levels.
Finally, realize that even though the PVXp 15 is a powerful and high output unit, it does ultimately have limits,
and it may need additional powered units (or a subwoofer) to provide enough sound output or coverage. In this
case, try turning the mixer levels down a little to see if that clears things up. If, after checking all the things
listed to check and anything else you can think of to check safely, and the system still exhibits problems,
carefully note all conditions and check with your Peavey dealer for advice.

cAre AnD MAintenAnce

Your PVXp 15 is a sturdy and durable product and will provide years of reliable use if properly cared for. Use
common sense and read the safety warnings to avoid hazardous operating conditions.
The unit must be disconnected from the AC power source before any work is done on it. Refer all servicing to
qualified service personnel.
Sunlight/Heat
Avoid prolonged exposure to direct sunlight, as this may cause the unit to overheat and thermally shut off.
Excessively hot operating conditions can also cause a thermal shutdown. Do not store in extremely hot or cold
conditions or extremely high humidity. Always allow unit to come to room temperature before use.
Cleaning
Never clean the PVXp 15 while plugged in or turned ON! When the unit has been fully disconnected from AC
power sources, use a dry cloth to remove soil or other dirt. Never use strong solvents on the PVXp 15, as they
could damage the cabinet. Do not allow ANY fluids to drip inside the PVXp 15.
Touchup
For an overall finish enhancement and protective coating, use gloves to apply a plastic finish protector, such as
Armor-All protectant or a similar product, to the surface of the plastic cabinet only. Note that the cabinet will be
®
slippery after these treatments; rub them down vigorously with a dry, lint-free cloth to minimize this.
Check for Secure Hardware
After the first few months of use and periodically thereafter, check the hardware of the PVXp 15 for tightness,
including the rear panel screws and the screws that hold the baffle and rear cabinet together. The unit is subject
to a great deal of vibration, and this could cause them to loosen with use.