Herunterladen Inhalt Inhalt Diese Seite drucken

Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TE-MS 18/210 Li Originalbetriebsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
Important! The cutting angle of the teeth, in
other words the direction of rotation of the
saw blade (7) must coincide with the direction
of the arrow on the housing.
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
Important! Every time that you change the
saw blade, check to see that it spins freely in
the table insert (12)in both perpendicular and
45° angle settings.
Important! The work to change and align the
saw blade (7) must be carried out correctly.
6.9 Transport (Fig. 1-3)
Retighten the locking screw (14) to secure the
turntable (17) in place.
Activate the release button (3), press the ma-
chine head (4) downwards and secure with
the safety pin (25). The saw is now locked in
its bottom position.
Carry the machine by the fixed transport
handle.
To set up the equipment again, proceed as
described in section 5.2.
6.10 Operating the laser (Fig. 2)
To switch on: Move the On/Off switch (36) to the
"I" position to switch on the laser (35). A laser line
is projected onto the material you wish to pro-
cess, providing an exact guide for the cut.
To switch o : Move the On/Off switch (36) to the
"0" position.
6.11 Operating the LED lamp (Fig. 2)
For good illumination of the work area you
can use the LED lamp in addition to the room
lighting. The On/Off switch (24) for the LED
lamp is on the top of the machine head, bet-
ween the handle (1) and the mount for the
rechargeable battery (40).
Switching on: Switch position „I"
Switching off: Switch position „0"
6.12 Electric brake
For safety reasons, the equipment is supplied
with an electric brake system for the saw blade.
The equipment may therefore emit an odor or
generate sparks when it is switched off . This has
no infl uence on the operational performance or
safety of the equipment.
Anl_TE_MS_18_210_Li_SPK13.indb 25
GB
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the battery pack before starting
any cleaning work.
7.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Important! The carbon brushes should not be re-
placed by anyone but a qualifi ed electrician.
7.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
- 25 -
26.04.2023 15:53:56

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

43.008.90

Inhaltsverzeichnis