Miscellaneous Settings; Setting The Clock - Makita MR001GZ Betriebsanleitung

Recalling a preset in AM/FM mode
1. Press the Power button to switch on your radio.
2. Press the Band button to select AM or FM radio mode.
3. Momentarily press the required Preset button, the
preset number and station frequency will appear on the
display.

MISCELLANEOUS SETTINGS

Setting the clock

Clock can be set either when the radio is power on or off.
1. Long press the Time set button for more than 2
seconds, the display will flash time set symbol and the
hour digit, followed by a beep.
2. Rotate the Tuning control knob to set the required hour.
3. Press the Tuning control knob to confirm hour setting,
the minute digit will flash.
4. Rotate Tuning control knob to set the required minute.
5. Press the Tuning control knob to complete clock
setting.
Setting the radio alarm
When the radio alarm is selected, the radio will turn on
and play the chosen radio station at the chosen alarm
time. The radio alarm will continue for one hour unless
turned off by pressing the Power button. Pressing the
Power button whilst the alarm is activated will cancel the
alarm for 24 hours.
Note:
When the radio is in low battery status, the radio alarm
can't be activated.
a. Setting radio alarm time:
1. Ensure that the clock time is set correctly before setting
the alarms. The radio alarm can be set either when
radio is on or off.
2. Press the Radio alarm button, the radio alarm symbol
will flash.
3. During radio alarm symbol flashing, press and hold
Time set button for more than 2 seconds followed by a
beep. The hour digit will flash on the display.
4. Rotate the Tuning control knob to select the required
alarm hour then press the Tuning control knob to
confirm the setting. The minute digit will flash on the
display.
5. Rotate the Tuning control knob to select the required
alarm minute. Press Tuning control knob to complete
the alarm time setting.
b. Setting radio alarmed station:
1. During setting radio alarm time and the radio alarm
symbol is flashing, press Band button to activate the
radio to select required wake-up band and station by
manual tuning or recall the preset stations. Rotate the
Tuning control knob to adjust the volume level. Press
the Time set button to complete radio alarm setting.
The display will show radio alarm symbol.
When the radio alarm is activated, the alarm will go
off in the Humane Waking System. It will increase its
volume from 0 to your set volume.
2. When above radio alarm time and station are set, press
and hold the Radio alarm button for 2 seconds followed
by a beep to switch alarm on or off. Display will show
radio alarm symbol when radio alarm is set.
Note:
●  I f new radio alarm station is not selected, it will select
the last alarm station.
●  I f the selected AM/FM alarm station is not available
when the alarm is sounding, the buzzer alarm will be
used instead.
Setting the HWS
(Humane Waking System) buzzer alarm
A beep tone will activate when selecting the HWS buzzer
alarm.
The alarm beep will sound shorter every 15 seconds
for one minute followed by one minute silence before
repeating the cycle.
The HWS alarm will sound for one hour until turning off by
pressing the Power button. Press the Power button whilst
the alarm is activated will cancel the alarm for 24 hours.
1. Ensure that the clock time is set correctly before setting
the alarms. The buzzer alarm can be set either when
the radio is on or off.
2. Press the Buzzer alarm button, the buzzer alarm
symbol will flash.
3. During the buzzer alarm symbol flashes, press and
hold the Time set button for more than 2 seconds
followed by a beep and the hour digit will flash on the
display.
4. Rotate the Tuning control knob to select the required
alarm hour then press the Tuning control knob to
confirm the setting. The minute digit will flash on the
display.
5. Rotate the Tuning control knob to select the required
alarm minute. Press Tuning control knob to complete
the buzzer alarm setting.
6. Press and hold the Buzzer alarm button for more than
2 seconds followed by a beep to switch on or off the
HWS buzzer alarm. Display will appear the buzzer
alarm symbol when buzzer alarm has been set.
Snooze
1. Whilst the alarm is activated, pressing any buttons
except the Power button will activate the snooze
function. The radio or HWS buzzer alarm will be
silenced with interval of 5 minutes.
10 ENGLISH