Makita HR002G Betriebsanleitung Seite 20

Chipping/Scaling/Demolition
Set the action mode changing knob to the
Hold the tool firmly with both hands. Turn the tool on
and apply slight pressure on the tool so that the tool will
not bounce around, uncontrolled.
Pressing very hard on the tool will not increase the
efficiency.
► Fig.34
Drilling in wood or metal
CAUTION:
Hold the tool firmly and exert care
when the drill bit begins to break through the
workpiece. There is a tremendous force exerted on
the tool/drill bit at the time of hole break through.
CAUTION:
A stuck drill bit can be removed
simply by setting the reversing switch to reverse
rotation in order to back out. However, the tool
may back out abruptly if you do not hold it firmly.
CAUTION:
Always secure workpieces in a
vise or similar hold-down device.
NOTICE:
Never use "rotation with hammering"
when the drill chuck is installed on the tool. The
drill chuck may be damaged.
Also, the drill chuck will come off when reversing the tool.
NOTICE:
Pressing excessively on the tool will not
speed up the drilling. In fact, this excessive pressure will
only serve to damage the tip of your drill bit, decrease the
tool performance and shorten the service life of the tool.
Set the action mode changing knob to the
For HR001G/HR003G
Optional accessory
Attach the chuck adapter to a keyless drill chuck to
which 1/2"-20 size screw can be installed, and then
install them to the tool. When installing it, refer to the
section "Installing or removing drill bit".
► Fig.35: 1. Keyless drill chuck 2. Chuck adapter
For HR002G/HR004G
Use the quick change drill chuck as standard equip-
ment. When installing it, refer to "changing the quick
change chuck for SDS-plus".
Hold the ring and turn the sleeve counterclockwise to open the
chuck jaws. Place the bit in the chuck as far as it will go. Hold the
ring firmly and turn the sleeve clockwise to tighten the chuck.
► Fig.36: 1. Sleeve 2. Ring
To remove the bit, hold the ring and turn the sleeve
counterclockwise.
Diamond core drilling
NOTICE:
If performing diamond core drilling
operations using "rotation with hammering"
action, the diamond core bit may be damaged.
When performing diamond core drilling opera-
tions, always set the action mode changing knob to
the position to use "rotation only" action.
Beating dust on the filter
Optional accessory
symbol.
CAUTION:
while the dust case is removed from the dust collec-
tion system. Doing so may cause dust inhalation.
CAUTION:
turning the dial on the dust case. Turning the dial
while the tool is running may result in the loss of
control of the tool.
By beating the dust on the filter inside the dust case,
you can keep the vacuum efficiency and also reduce
the number of times to dispose of the dust.
Turn the dial on the dust case three times after col-
lecting every 50,000 mm
vacuum performance declined.
NOTE: 50,000 mm
holes of ø10 mm and 65 mm depth (14 holes of ø3/8"
and 2" depth).
► Fig.37: 1. Dust case 2. Dial
Disposing of dust
Optional accessory
CAUTION:
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
disposing of dust.
symbol.
CAUTION:
before the dust case becomes full. Failure to do so
may decrease the dust collection performance and
cause dust inhalation.
CAUTION:
decreases if the filter in the dust case become
clogged. Replace the filter with new one after
approximately 200 times of dust fulfillment as a
guide. Failure to do so may cause dust inhalation.
1. Remove the dust case while pressing down the
lever of the dust case.
► Fig.38: 1. Lever
2. Open the cover of the dust case.
► Fig.39: 1. Cover
3.
Dispose of the dust, and then clean the filter.
► Fig.40
NOTICE:
of the filter gently by hand to remove dust. Do not
tap the filter directly; touch the filter with brush
or similar; or blow compressed air on the filter.
Doing so may damage the filter.
Blow-out bulb
Optional accessory
After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.
► Fig.41
20 ENGLISH
Do not turn the dial on the dust case
Always switch off the tool when
3
of dust or when you feel the
3
of dust equivalents to drilling 10
Always be sure that the tool is
Be sure to wear dust mask when
Empty the dust case regularly
The performance of dust collection
When cleaning the filter, tap the case