Noise/Vibration Information; Charging The Battery - Bosch ANGLE EXACT 12V-12-400 Originalbetriebsanleitung

Industrial cordless screwdriver
ANGLE EXACT
C)D)
Maximum Power Boost speed
Max. torque, hard/soft screwdriving applic-
C)
ation according to ISO 5393
C)E)
Maximum torque
Weight according to
A)
EPTA-Procedure 01:2014
A) Depends on battery in use
B) Limited performance at temperatures < 0 °C
C) Measured at 20–25 °C with rechargeable battery GBA 12V 6.0Ah.
D) Limited performance at speeds < 50 %)
E) Only possible in cycle operation: < 5 screws driven in per minute
Article number
Torque, hard/soft screwdriving
application according to VDI
A)
2647
Tightening torque at the flange
Weight according to EPTA-Pro-
cedure 01:2014
A) The homologation according to VDI 2647 can be downloaded from www.bosch-professional.com.

Noise/vibration information

Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted sound pressure level of the power
tool is less than 70 dB(A). The noise level when working can
exceed the volume stated. Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2:
Impact tightening of fasteners of the maximum capacity of
2
the tool: a < 2,5 m/s , K = 1,5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Bosch Power Tools
12V-12-400
-1
min
Nm
Nm
kg
Angled screw head
■ 1/4" ■ 3/8"
0 607 453 0 607 453 0 607 453
617 620
Nm 20 25
Nm 20 20
kg 0.20 0.20
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
u
2

Charging the Battery

u
Note: The battery is supplied partially charged. The state of
charge is not sufficient to start up the tool. To ensure full bat-
tery capacity, fully charge the battery in the charger before
using your tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by "Electronic Cell Protection (ECP)". When the battery is
discharged, the power tool is switched off by means of a pro-
tective circuit: The application tool no longer rotates.
12V-6-600
650 1040
2.5–8.0 1.5–4.5
9.0 4.5
1.0−1.4 1.0−1.4
■ 3/8"
1/4" QC
1/4"
0 607 453 0 602 496
618 630 020
20 20 15
20 20 15
0.20 0.20 0.15
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
1 609 92A 6RK | (09.11.2021)
English | 19
12V-3-600
1040
0.8–2.5
2.5
1.0−1.4
Adapter
QC
1/4"
0 602 496 0 602 496
021 022
15 20
15 20
0.15 0.05