EINHELL 34.365.10 Originalbetriebsanleitung Seite 22

Functions
Vibration emission value a
K uncertainty = 1.5 m/s
GC-BC 30 AS
Engine type .........................................................
........ 2-stroke engine, air-cooled, chrome cylinder
Engine power (max.) ................... 0.9 kW (1.2 HP)
Displacement ...........................................31 ccm
Idle speed of engine .................. 3100 ∓ 200 min
Max. engine speed...............................9500 min
Max. torque
Scythe: ................................................7200 min
Trimmer: ..............................................6400 min
Ignition .................................................Electronic
Drive ........................................Centrifugal clutch
Weight (with empty tank) ............................6.1 kg
Cutting line diameter ...................................45 cm
Cutting circle diameter of blade ..................23 cm
Cutting line length ......................................... 4 m
Cutting line diameter: ................................. 2 mm
Tank capacity ................................................0.4 l
Spark plug ................................................ L8RTC
Danger!
Sound and vibration
L sound pressure level ........................ 95 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 114 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Functions
Vibration emission value a
K uncertainty = 1.5 m/s
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Anl_GC_BC_25_30_AS_SPK1.indb 22 Anl_GC_BC_25_30_AS_SPK1.indb 22
= 6.4 m/s
2
h
2
-1
-1
-1
-1
= 6.4 m/s
2
h
2
- 22 -
GB
5. Assembly
5.1.1 Fitting the steady grip
Install the steady grip as shown in Figures 3a-3c.
Do not tighten the screws until you have set the
perfect working position with the carrying strap.
The steady grip should be aligned as shown in
Figure 1. To dismantle, proceed in reverse order.
5.1.2 Fitting the long handle (Fig. 4a – 4c)
Pull the locking lever (A) and push the long hand-
le (Fig. 4b/Item 2) carefully into the connecting
piece of the long handle. While doing so, make
sure that the drive shafts on the inside of the long
handle slide into each other (turn the spool head
slightly if required). The lug of the locking lever
(A) must latch into the hole (B). Now tighten the
handle screw (21) as shown in Figure 4c.
5.1.3 Fitting the blade guard hood
Important: The cutting blade guard hood must be
fi tted if you wish to work with the cutting blade.
The guard hood for the cutting blade must be ins-
talled as shown in Figures 5a – 5b.
5.1.4 Fitting/Replacing the cutting blade
The fi tting of the cutting blade is shown in Figures
6a – 6g. To dismantle, proceed in reverse order.
•
Fit the carrier plate (22) onto the spline shaft
(Fig. 6b)
•
Securely fit the cutting blade (18) on the co-
ver ring (Fig. 6c)
•
Place the pressure plate (23) over the thread
of the spline shaft (Fig. 6d).
•
Plug on the cover of the pressure plate (24)
(Fig. 6e).
•
Look for the hole in the carrier plate, line up
with the notch underneath, lock with the sup-
plied Allen key (28), and tighten the nut (25)
(Fig. 6f/6g). Important: Left-hand thread
5.1.5 Fitting the cutting line guard hood to
the blade guard hood
Important: The cutting line guard hood must be
additionally fi tted if you want to work with the cut-
ting line (Fig. 7a/Item 14).
The guard hood for the cutting line must be ins-
talled as shown in Figures 7a – 7b. A blade (Fig.
7a/ Item F) on the underside of the guard hood
automatically cuts the cutting line to the optimum
length. This is covered by a guard (Fig. 7a/Item
G).
Remove the guard before you start working and
replace it when you have fi nished working.
21.10.2016 11:59:28 21.10.2016 11:59:28