Herunterladen Inhalt Inhalt Diese Seite drucken

General Power Tool Safety Warnings - Makita DCS551ZJ Betriebsanleitung

Akku-metall-handkreissäge
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 17
ENGLISH (Original instructions)
1.
Button
2.
Red indicator
3.
Battery cartridge
4.
Indicator lamps
5.
Check button
6.
Switch trigger
7.
Lock-off lever
8.
Battery indicator
9.
Mode indicator
10. Lever
SPECIFICATIONS
Blade diameter
Max. Cutting depth
No load speed
Overall length (with BL1830)
Rated voltage
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting in mild steel.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
CORDLESS METAL CUTTER
SAFETY WARNINGS
Cutting procedures
1.
DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on
auxiliary handle, or motor housing. If both hands
are holding the tool, they cannot be cut by blade.
2. Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the
workpiece.
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
4. Never hold piece being cut in your hands or
across your leg. Secure the workpiece to a stable
platform. It is important to support the work properly
4
Explanation of general view
11. Alignment line
12. Cutting line
13. Base
14. Lamp
15. Shaft lock
16. Hex wrench
17. Hex bolt
18. Outer flange
19. Saw blade
20. Inner flange
Model
Net weight
to minimize body exposure, blade binding, or loss of
ENE022-1
control.
5. Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting tool may contact hidden wiring. Contact
GEA010-1
with a "live" wire will also make exposed metal parts of
the power tool "live" and could give the operator an
electric shock.
6. When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
7. Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the tool
will run eccentrically, causing loss of control.
8. Never use damaged or incorrect blade washers or
bolt. The blade washers and bolt were specially
GEB058-4
designed for your tool, for optimum performance and
safety of operation.
Kickback causes and related warnings
Kickback is a sudden reaction to a pinched, bound or
misaligned blade, causing an uncontrolled tool to lift
up and out of the workpiece toward the operator.
When the blade is pinched or bound tightly by the kerf
closing down, the blade stalls and the motor reaction
drives the unit rapidly back toward the operator.
If the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into the
top surface of the workpiece causing the blade to
climb out of the kerf and jump back toward the
operator.
21. Cup washer
22. Hook
23. Screw
24. Front grip
25. Rear handle
26. Sight grooves
27. Clamp screw
28. Rip fence (Guide rule)
DCS551
150 mm
57.5 mm
-1
3,900 min
332 mm
D.C. 18V
2.9 kg

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Dcs551

Inhaltsverzeichnis