Bosch 0601B42001 Originalbetriebsanleitung Seite 35

– If you require one of these parts, remove it carefully from
its storage location.
Positioning the riving knife (see figures b1–b2)
Note: If necessary, clean all parts to be fitted before you po-
sition them.
– Turn the crank (15) clockwise as far as possible so that
the saw blade (24) is in the highest possible position
above the saw table.
– Release the clamping lever (34) clockwise until it points
upwards.
– Slide the riving knife (4) towards the clamping lever (34)
until it can be pulled upwards.
– Pull the riving knife all the way up until it is positioned ex-
actly over the centre of the saw blade.
– Allow both pins (35) to engage in the lower bore holes in
the riving knife and then retighten the clamping lever
(34).
The markings (33) on the clamp and clamping lever (34)
must be aligned as shown.
Fitting the table insert (see figure c)
– Place the table insert (23) over the riving knife (4) and
into the tool chamber.
– Turn the locking screw (36) as far as it will go in the
"Lock" direction using the tip of the ring spanner (9).
The front side of the table insert (23) must lie flush with or a
little below the saw table; the rear must lie flush with or a
little above the saw table.
Fitting the protective cover (see figures d1–d2)
Note: Only fit the protective cover when the riving knife is in
the top position directly over the centre of the saw blade
(see figure b2). Do not fit the protective cover when the riv-
ing knife is in the bottom position (position when delivered/
position for sawing grooves) (see figure b1).
– Loosen the clamping lever (37) and remove the protect-
ive cover (3) from the bracket (11).
– Hold the saw blade guard (upper metal rail) of the pro-
tective cover (3) with one hand, while using the other
hand to move the clamping lever (37) up.
– Push the guide pin (38) backwards into the groove on the
riving knife (4).
– Move the protective cover (3) down until the saw blade
guard (upper metal rail) is parallel with the surface of the
saw table (21).
– Push the clamping lever (37) down. The clamping lever
must be felt and heard to engage; the protective cover (3)
must be securely and safely fitted.
Always check that the blade guard can move properly
u
before use. Do not use the power tool if the blade
guard cannot move freely and does not close immedi-
ately.
Fitting the parallel guide (see figure e)
The parallel guide (5) can be positioned on either the left or
the right of the saw blade.
Bosch Power Tools
– Loosen the clamping handle (39) of the parallel guide
(5). This lightens the load on the V guide (40).
– First insert the parallel guide with the V guide into the
guide groove (30) of the saw table. Then position the par-
allel guide in the front guide groove (25) of the saw table.
The parallel guide can now be moved freely.
– To secure the parallel guide, push the clamping handle
(39) down.
Fitting the additional parallel guide (see figure f)
To saw narrow workpieces and bevel angles, you must fit
the additional parallel guide (41) on the parallel guide (5).
The additional parallel guide can be fitted on the left or right
of the parallel guide (5) as required.
Use the "additional parallel guide" fastening set (42) (two
fastening screws, two washers, two wing nuts) for fitting the
guide.
– Slide the fastening screws through the lateral holes on the
parallel guide (5).
– The heads of the screws are used to guide the additional
parallel guide.
– Slide the additional parallel guide (41) over the heads of
the fastening screws.
– Place the washers on the fastening screws and tighten the
screws using the wing nuts.
Fitting the angle guide (see figure g)
– Push the rail (43) of the angle guide (2) into one of the
guide grooves (28) provided in the saw table.
Stationary or flexible mounting
To ensure safe handling, the power tool must be
u
mounted on a flat, stable work surface (e.g. work
bench) before use.
Mounting on a work surface (see figure h)
– Use suitable screw fasteners to secure the power tool to
the work surface. The holes (8) are used for this purpose.
Mounting on a Bosch saw stand (see figure i)
Thanks to their height-adjustable legs, Bosch saw stands
(e.g. GTA 560) provide firm support for the power tool on
any surface.
Read all the warnings and instructions included with
u
the saw stand. Failure to observe the warnings and fol-
low instructions may result in electric shock, fire and/or
serious injury.
Assemble the saw stand properly before mounting the
u
power tool. Correct assembly is important to prevent the
risk of collapsing.
– Mount the power tool on the saw stand in the transport
position.
Dust/chip extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
English | 35
1 609 92A 5UC | (18.09.2020)