Factory Settings; Dip Switches - Niko 350-20082 Gebrauchsanleitung

Read the complete manual before carrying out the installation and activating the system. Keep
the manual for future reference.
1. DESCRIPTION
The presence or absence detector 360° (master) for surface mounting consists of an integral unit
with on-off control of two channels, a motion sensor (PIR or passive infrared technology), a light sensor and
an integrated IR receiver. All external units, such as push buttons and lighting fixtures, are directly connected
to the detector, which is surface-mounted onto the ceiling.
This detector can be used as a stand-alone unit or as a master in combination with one or more secondary
detectors (350-20079, 350-20071 or 350-20081).
The detector can be installed and operated on the basis of the factory settings. For optimal lighting control,
it is recommended to adjust the factory settings to the environmental conditions and to the specific lighting
requirements. The settings can be adjusted to your preference using the integrated potentiometers and DIP
switches on the device or using the IR remote control (not included) (350-20089) or the universal remote
control for smartphone (not included) (350-41936).
2. INSTALLATION
2.1. Connection
Danger: Disconnect all power before installing the detector.
Do not connect the device to the mains voltage until installation has been completed.
A. Stand-alone
Refer to the wiring diagram (fig. 1A).
B. In combination with one or more secondary detectors
Refer to the wiring diagram (fig. 1B).
2.2. Mounting
Tip: Do not install the detector in the vicinity of heat sources such as stoves or electric heaters, air currents
(ventilation systems) or any moving objects (fig. 2). This can activate the device unnecessarily as it reacts
to motion and heat in its surroundings.
Tip: The recommended mounting height is 2 to 3.4 m. At a height of 3 m, the detector has a 24 m diameter
range (fig. 3)
3. SETTINGS

3.1. Factory settings

At delivery the parameters of the detector are set as follows:
Parameter Factory setting
application - DIP switch 1: channel 1 automatic on/off (= presence detector)
- DIP switch 2: channel 2 automatic on/off (= presence detector)
- DIP switch 3:
• pressing the push button briefly allows you to switch the light on or off (= eco off)
• pressing the button for longer allows you to switch the light permanently on or
off for a period of 2 hours, excluding the switch-off delay
- DIP switch 4: a brief press is daylight-dependent
sensitivity of the high, both channels
motion sensor
light sensitivity 200 lux, both channels
switch-off delay 10 min, both channels

3.2. DIP switches

Figure 5 shows how to set the DIP switches according to the application and the desired sensitivity of
the motion sensor.
Application setting
DIP switch Application
1 You can set channel 1 on the detector:
- ON: as presence detector (automatic on/off)
The detector automatically switches on the lighting, depending on the preset lux
value and when motion is detected.
- OFF: as absence detector (manual on/automatic off)
The detector only switches on the lighting when you press the push button briefly,
depending on the preset lux value.
The lighting will remain on for the duration of the preset switch-off delay after the last
motion is detected. As soon as the switch-off delay has elapsed, the lighting switches off.
You can set channel 2 on the detector:
2
- ON: as presence detector (automatic on/off)
The detector automatically switches on the lighting, depending on the preset lux
value and when motion is detected.
- OFF: as absence detector (manual on/automatic off)
The detector only switches on the lighting when you press the push button briefly,
depending on the preset lux value.
The lighting will remain on for the duration of the preset switch-off delay after the last
motion is detected. As soon as the switch-off delay has elapsed, the lighting switches off.
3 You can also make a selection from several functions for the push buttons that
are connected:
- ON: You can only switch on the lighting with a brief press. The 'eco off' and
'long push' functions are deactivated.
- OFF: With a brief press, the lighting can be either switched on or switched
off immediately without having to wait for the switch-off delay (= eco off
the lighting is switched off with the push button, the detector will be locked for ten
seconds to avoid the lighting from immediately being switched on again.
If you press the push button for longer than one second, the red indication LED will flash
(0.25 s on and 5 s off). The lighting and the preset switch-off delay will be activated or
deactivated for two hours.
- ON: A brief press is daylight-independent.
4
- OFF: A brief press is daylight-dependent.
A long push is always daylight-independent.
PM350-20082R23042
The 'eco off' function is the most energy-efficient way to switch on the lighting. You switch off the lighting yourself
1
without having to wait for the switch-off delay. If you do forget to switch off the lighting, it will be switched off
automatically after the switch-off delay has elapsed.
Sensitivity setting
Using the two DIP switches located on the very right you set the sensitivity of the motion sensor. You can choose
from the following options: minimum, low, high or maximum. Refer to figure 5 for the position of the DIP switches
depending on the desired sensitivity.
3.3 Setting one push button for both channels
This function allows you to control both channels with only one 230 V push button. This is particularly useful in
corridors and stairwells where the armatures are divided into different light groups.
With this function you can:
• Briefly press once to switch the light off (= eco off) if the detector functions as a presence detector (DIP
switch 1 and 2 ON)
Lock/ Light 1 Light 2
• Briefly press once to switch the light on or off if the detector functions as an absence detector (DIP switch 1 and
unlock On/Off On/Off
2 OFF). It does not matter whether the push-button is connected to T1/S or T2. When the function is activated,
channel 1 will switch on first and channel 2 will switch on immediately afterwards. 20 50 100
Lux Lux Lux
Important! T1/S and T2 may never be short-circuited or connected in parallel.
300
Learn actual lux
Lux
3.3.1 One short push for both channels
You can programme this function with the IR remote control (not included) (350-20089) as follows:
500 700 1000
Lux Lux Lux
1. Unlock the device by pressing
Lock/ Light 1 Light 2 LED
unlock On/Off On/Off On/Off
2. Press to select channel 1. Status
Ch 1 Ch 2
Ch 1
20 50 100 200
The detector will confirm by flashing red.
Lux Lux Lux Lux
Pulse 2min 5min
3. Press .
300 400
Learn actual lux
Lux Lux
The detector will confirm by flashing red.
15min 30min 60min
4. Press again.
500 700 1000 No
Lux Lux Lux Lux
The detector will confirm by flashing red twice. Channel 1 has now been activated. Test Short Long
On/Off push push
5. Press to select channel 2.
Status Status
Ch 1 Ch 2
Ch 1 Ch 2
The detector will confirm by flashing blue.
Pulse 2min 5min 10min
6. Press .
The detector will confirm by flashing blue.
8
15min 30min 60min
Hours
7. Press again.
The detector will confirm by flashing blue twice. Channel 2 has now been activated. Test Short Long Fact.
On/Off push push setting
Lock/ Light 1 Light 2
unlock On/Off On/Off
8. Lock the device by pressing
The detector will confirm by flashing green twice.
20 50 100
Lux Lux Lux
Both channels will work when a push button which is connected to T1/S or T2 is briefly pressed once.
300
Learn actual lux
Lux
Lock/ Light 1 Light 2 LED
unlock On/Off On/Off On/Off
To cancel this function again with the IR remote control (not included) (350-20089), proceed as follows:
500 700 1000
Lux Lux Lux
1. Unlock the device by pressing 20 50 100 200
Lux Lux Lux Lux
2. Press to select channel 1. Status
Ch 1 Ch 2
Ch 1
300 400
Learn actual lux
Lux Lux
The detector will confirm by flashing red.
Pulse 2min 5min
3. Press .
500 700 1000 No
Lux Lux Lux Lux
The detector will confirm by flashing red. Channel 1 has now been deactivated.
15min 30min 60min
4. Press to select channel 2.
Status Status
Ch 1 Ch 2
Ch 1 Ch 2
The detector will confirm by flashing blue. Test Short Long
On/Off push push
Pulse 2min 5min 10min
5. Press .
The detector will confirm by flashing blue. Channel 2 has now been deactivated.
8
15min 30min 60min
Hours
6. Lock the device by pressing
Lock/ Light 1 Light 2
The detector will confirm by flashing green twice. Test Short Long Fact.
unlock On/Off On/Off
On/Off push push setting
Both channels can now be activated separately, each with their own push button which is respectively connected
20 50 100
Lux Lux Lux
with T1/S and T2.
300
Learn actual lux
Lux
3.3.2 One long push (> 1 sec) for both channels
You can programme this function with the IR remote control (not included) (350-20089) as follows:
500 700 1000
Lux Lux Lux
1. Unlock the device by pressing
Lock/ Light 1 Light 2 LED
unlock On/Off On/Off On/Off
2. Press to select channel 1. Status
Ch 1 Ch 2
Ch 1
The detector will confirm by flashing red. 20 50 100 200
Lux Lux Lux Lux
Pulse 2min 5min
3. Press .
300 400
Learn actual lux
The detector will confirm by flashing red twice. Lux Lux
15min 30min 60min
4. Press again.
500 700 1000 No
Lux Lux Lux Lux
The detector will confirm by flashing red twice. Channel 1 has now been activated.
Test Short Long
On/Off push push
5. Press to select channel 2. Status Status
Ch 1 Ch 2
Ch 1 Ch 2
The detector will confirm by flashing blue.
Pulse 2min 5min 10min
6. Press .
The detector will confirm by flashing blue.
8
15min 30min 60min
Hours
7. Press again.
). When
1
The detector will confirm by flashing blue twice. Channel 2 has now been activated. Test Short Long Fact.
On/Off push push setting
Lock/ Light 1 Light 2
unlock On/Off On/Off
8. Lock the device by pressing
The detector will confirm by flashing green twice.
20 50 100
Lux Lux Lux
Both channels will work if the push button which is connected to T1/S or T2 is held down once.
300
Learn actual lux
Lux
To cancel this function again with the IR remote control (not included) (350-20089), proceed as follows:
500 700 1000
Lux Lux Lux
1. Unlock the device by pressing
2. Press to select channel 1. Status
Ch 1 Ch 2
Ch 1
Pulse 2min 5min
LED
On/Off
200
Lux
400
Lux
No
Lux
three times within five seconds.
Lock/ Light 1 Light 2 LED
unlock On/Off On/Off On/Off
Status
Ch 2
20 50 100 200
Lux Lux Lux Lux
10min
300 400
Learn actual lux
Lux Lux
8
Hours
500 700 1000 No
Lux Lux Lux Lux
Fact.
setting
Status Status
Ch 1 Ch 2
Ch 1 Ch 2
Pulse 2min 5min 10min
8
15min 30min 60min
Hours
Test Short Long Fact.
On/Off push push setting
LED
On/Off
three times.
Lock/ Light 1 Light 2 LED
unlock On/Off On/Off On/Off
200
Lux
20 50 100 200
Lux Lux Lux Lux
400
Lux
300 400
Learn actual lux
Lux Lux
No
Lux
500 three times within five seconds. 700 1000 No
Lock/ Light 1 Light 2 LED
Lux Lux Lux Lux
unlock On/Off On/Off On/Off
Status
Ch 2
20 50 Status 100 Status 200
Ch 1 Ch 2
Lux Lux Ch 1 Lux Ch 2 Lux
10min
300 400
Pulse 2min 5min 10min
Learn actual lux
Lux Lux
8
Hours
8
500 700 1000 No
15min 30min 60min
Hours
Lux Lux Lux Lux
Fact.
setting
Test Short Long Fact.
Status Status
Ch 1 Ch 2
On/Off push push setting
Ch 1 Ch 2
Pulse 2min 5min 10min
three times.
Lock/ Light 1 Light 2 LED
unlock On/Off On/Off On/Off
LED
8
On/Off
15min 30min 60min
Hours
20 50 100 200
Lux Lux Lux Lux
200
Test Short Long Fact.
Lux
On/Off push push setting
300 400
Learn actual lux
Lux Lux
400
Lux
500 700 1000 No
Lux Lux Lux Lux
No
Lux
three times within five seconds.
Lock/ Light 1 Light 2 LED
Status Status
Ch 1 unlock Ch 2 On/Off On/Off On/Off
Ch 1 Ch 2
Status
Ch 2
20 50 100 200
Pulse 2min 5min 10min
Lux Lux Lux Lux
10min
300 400
8
Learn actual lux
15min Lux 30min 60min Lux
Hours
8
Hours
500 700 1000 No
Test Short Long Fact.
Lux Lux Lux Lux
On/Off push push setting
Fact.
setting
Status Status
Ch 1 Ch 2
Ch 1 Ch 2
Pulse 2min 5min 10min
8
15min 30min 60min
Hours
Test Short Long Fact.
On/Off push push setting
LED
On/Off
three times.
Lock/ Light 1 Light 2 LED
unlock On/Off On/Off On/Off
200
Lux
20 50 100 200
Lux Lux Lux Lux
400
Lux
300 400
Learn actual lux
Lux Lux
No
Lux
three times within five seconds.
500 Lock/ 700 Light 1 1000 Light 2 No LED
Lux unlock Lux On/Off Lux On/Off Lux On/Off
Status
Ch 2
Status Status
20 50 100 200
Ch 1 Ch 2
Ch 1 Ch 2
Lux Lux Lux Lux
10min
300 400
Pulse 2min 5min 10min
Learn actual lux
Lux Lux
8
350-20082
9
EN