Before Putting Into Operation - EINHELL HYPRESSO 18/24 Li Originalbetriebsanleitung

2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before putting into operation

Caution!
Protect your battery pack against moisture,
rain and high humidity. Make sure that no water
runs over the battery pack or its contacts during
operation.
Use the PXC battery protector (16) supplied with
the tool. First insert the battery in your PXC tool
(Fig. 10). As you do so, make sure that the con-
tacts on the tool and on the battery are dry. Now
pull the PXC battery protector (16) over the batte-
ry (Fig. 11). Make sure that PXC battery protector
is not damaged, is correctly seated and seals off
every contact surface from the tool. Always remo-
ve the PXC battery protector before you take the
battery out of the tool.
Warning!
Always pull out the battery before making
any settings on the equipment.
5.1 Using the equipment correctly
•
The tool must be stood on a level, stable
surface.
•
It is recommended that you adopt the correct
operating position every time you use the
equipment, i.e. one hand on the gun and the
other hand on the lance.
•
Never direct the water jet at electric cables or
at the equipment itself.
•
So that the pump does not suffer any damage
when it is not in use, a small amount of leaka-
ge from the pump is normal.
•
Never use the machine in potentially explosi-
ve areas under any circumstances!
•
The operating temperature must be between
+5 and + 40°C.
•
Do not cover or modify the lance or the spray
nozzles in any way.
•
The tool is designed to be used with cold or
lukewarm water (max. 40°C); higher tempera-
tures will result in damage to the pump.
•
Do not use water that is dirty, gritty or con-
tains any chemical products, as these could
Anl_Hypresso_18_24_Li_SPK13.indb 18 Anl_Hypresso_18_24_Li_SPK13.indb 18
GB
impair operation and shorten the life of the
equipment.
Warning – Risk of explosion
Do not spray fl ammable liquids.
Warning
Water that has passed through the non-return
valve is not drinkable.
Warning
If cleaning agent gets into contact with your skin
or into your eye, rinse immediately with lots of
clean water. Then consult a doctor or follow the
steps described on the safety data sheet or provi-
ded by the manufacturer of the cleaning agent.
5.2 Assembly
5.2.1 Fitting the extensions/nozzles (Fig. 2)
Various attachments can be fi tted to the gun. First
fi t the extensions (6) to the connector (13). Then
you can press the attachments into the extension
(you will encounter a slight spring resistance) and
secure by turning.
Important! Check that the attachment is secure
before you begin with the cleaning.
Nozzle attachment (8)
By turning the nozzle (8) you can change the sha-
pe of the water jet from a solid cone to a narrow
fl at fan, a wide fl at fan or rotation (Fig. 4).
Foam nozzle (7)
Open the foam nozzle (Fig. 6) by turning it, then
fi ll in foam cleaner. You can control the quantity of
foam by turning the foam adjuster (12).
5.2.2 Water inlet connector (Fig. 3)
The connection for the water inlet (5) is equipped
with a connector for standard hose coupling sys-
tems. Plug the supply hose coupling (min. Ø 1/2"
/ approx. 13 mm) onto the water inlet connector
(15), or use the supplied suction hose to use wa-
ter from a container. In this case always make use
of the suction hose fi lter (10).
A backfl ow stop must be installed between the
drinking water and the tool! Ask your local plum-
ber about this.
- 18 -
19.01.2023 15:47:01 19.01.2023 15:47:01