Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TP-AG 18/125 CE Q Li Originalbetriebsanleitung

still! You must keep the spindle lock pressed
while you change the wheel!
6.7 Test run for new grinding Wheels
Allow the right-angle grinder to run in idle for at
least 1 minute with the grinding or cutting wheel
fi tted in place. Vibrating wheels are to be replaced
immediately.
6.8 Grinding Wheels
•
Never use a grinding or cutting wheel bigger
than the specified diameter.
•
Before using a grinding or cutting wheel,
check its rated speed.
•
The maximum speed of the grinding or cut-
ting wheel used must be higher than the idle
speed of the angle grinder.
•
Use only grinding and cutting wheels that are
approved for a minimum speed of 10,500 rpm
and a peripheral speed of 69 m/sec.
•
Check the direction of rotation when you use
diamond cutting wheels. The directional arrow
on the diamond cutting wheel must point in
the direction in which the tool rotates.
Warning!
6.9 Operating Modes
6.9.1 Rough grinding (Fig.6)
Caution: Use the safety device for sanding/
grinding
For the best rough grinding results, hold the grin-
ding wheel at an angle of between 30° and 40° to
the workpiece surface and guide back and forth
over the workpiece in steady movements.
6.9.2 Cutting (Fig. 7)
Caution: Use the safety device for abrasive
cutting (Available as an accessory, see 7.3).
When you use the right-angle grinder for cutting
purposes, avoid tilting it in the cutting plane. The
cutting wheel must have a clean cutting edge.
A diamond cutting wheel is best used to cut hard
stone.
Warning!
It is prohibited to use the machine on asbes-
tos materials!
Warning!
Never use a cutting wheel for rough grinding.
Anl_TP_AG_18_125_CE_Q_Li_SPK13.indb 20 Anl_TP_AG_18_125_CE_Q_Li_SPK13.indb 20
GB
Note:
To increase the power and running time of the
cordless equipment, we recommend using our
4.0 Ah Power X-Change.
(Art. No.: 45.113.96)
Important!
To increase the cutting performance and running
time of the cordless equipment, we recommend
that you use a cutting wheel with a thickness of
1 mm.
6.10 Motor
It is vital for the motor to be well ventilated during
operation. Be sure, therefore, to keep the ventilati-
on holes clean at all times.
6.11 Removable dust guard (Fig. 8-10/Item 9)
The cordless angle grinder is equipped with a re-
movable dust guard in order to protect the motor
from too high a dust load. For cleaning purposes,
take off the removable dust guard (9) as shown in
Fig. 8, clean it with compressed air, and refi t it on
the tool as shown in Fig. 10.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the battery pack before starting
any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
- 20 -
28.11.2022 11:33:10 28.11.2022 11:33:10