Identification Of Parts; Assembly; Operation - Texas A/S COMBI 800 Bedienungsanleitung

Identification of parts

Figure 1:
A. Activation of wheels
B. Activation of accessory
C. Gear
D. Throttle
E. Accessory- Snowblade
F. Accessory – Snowthrower
G. Accessory- Sweeper
H. Supporting leg

Assembly

The machine is almost ready assembled from the
factory. Only a few items remain to be assembled:
1. Install the upper handlebar on the lower
handlebar using the supplied bolts.
See fig. 2-A (Do not tighten at this point)
2. Attach the dashboard to the upper handlebar
using the supplied bolts. See fig 2-C.
(Do not tighten at this point)
3. Tighten, the bolts at the upper handlebar on
the lower handlebar See fig.2-A.
4. Tighten, the dashboard bolts.See fig. 2-C.
5. Attach the clutch handles and fix the cables.
See figure 2-D.
6. Mount the gear rod
A. Attach the gear rod into the bottom
gear arm and turn approx. 2 rounds,
(links threaded)
B. Put the gear lever between R and 1.
C. Attache the gear rod into the top gear
arm and turn until gear lever snaps
into gear R.
D. Tighten the 2 nuts on the gear rod.
Follow the instructions in fig 2-B.
7. Mount the axle pole and wheels See fig 2-E
Note: "Arrow" on the tire should be pointing
forward
.
Check the tire pressure on both wheels before use.
Correct tire pressure is 30 psi/2 bar.
Use of machine with too low tire pressure,
can damage the tires!
Assembly of accessory
Follow the assembly procedure as shown in fig 3

Operation

Read the instruction manual for the engine,
before use.
Before using the machine, remove all foreign objects
from the vicinity. Stones, glass, branches and similar
items can damage the machine. Also check that all
bolts are tightened.
Control oil level before starting the engine.
See attached guide
Start the engine:
1. Open the fuel tap.
2. On a cold engine open the choker.
Note: By a hot engine choke is not required.
3. Turn the throttle cable to "start" position.
4. Pull the recoil starter gently until you feel
resistance in the rope. Then pull quickly and
energetic. Do not at any time let go of the
recoil starter but glide it gently back and pull
again.
5. Regulate the choker until the engine is running
smoothly.
Stop the engine:
Pull the throttle lever to "STOP" in order to stop the
1.
engine.
Remember to close the fuel valve if the machine will
not be used over a longer period !
Clutch Lever A - Forward and Reverse.
To operate the black clutch lever A in Fig. 6, the
control stick must first be activated. By tilting the
control stick to the right or left side and then activate
the black handle, the machine will move forward or
backwards. To change direction release the lever and
enterthe desired gear postion.
Gear: The machine has 4 forward and 1 reverse gear.
To change gear release the clutch lever fig. 6 A and
select the disered gear Fig 6 D
Gear R
2,3
Speed
Km/h
Snowblower-accessory: It is recommended only to use
first gear in snow depth from 10 cm and above. The
snow clearing work deteriorate at speeds above 1,5
km/h.
Pay attention while reversing. It is important that the
area is cleared, for any obstacle before reversing.
Never reverse the machine against a wall, tree or any
other fixed obstacle.
Clutch Lever B - Activation of accessory.
To operate the black brush lever B in Fig. 6, the control
stick must first be activated. By tilting the red stick
completely to the right and then push the lever down
activates the accessory
Important! The red control stick on the clutch lever
must be pushed to the far right before the clutch lever
is activated. If not the clutch lever will forced of its hold.
If this happens, push the lever back up and repeat the
procedure. See Fig.6 A+B.
Note: The clutch lever is not broken but simply pushed
back into place.
The machine is equipped with a "dead man's handle",
once released the brush and drive will stop
immediately.
Differential lock - mechanical:

Disable see Figure 4-A

Enable see Figure 4-B
10
1 2 3
1,5 2,9 4,4
Km/h Km/h Km/h
4
5,8
Km/h