Identification Of Parts; Fitting; Assembling The Machine; Operation - Texas A/S Smart Sweep 800 Bedienungsanleitung

Identification of parts

Figure 2:
A. Control of brush rpm
B. Clutch handle – to activate operation
C. Handle bars
D. Adjustment of oversteering
E. Brush angle support rod
F. Engine
G. Gear selector
H. Wheel
I. Support wheel for brush
J. Clutch handle – to activate brushes
K. Throttle
L. Underside.
M. Adjustment of sweeping height
N. V-belt guard
O. Fitting for snow scraper blade/collection box
P. Brush

Fitting

The actual model can vary from the illustrations
shown.
Check the tyre pressure on both wheels before use.
The correct tyre pressure is 30 psi/2 bar. Figure 7.
Operating the machine with tyre pressure that
is too low can destroy the tyres and hose!

Assembling the machine

The sweeper is supplied from the factory almost ready
for operation. Only a few parts need to be fitted.
1. Figure 3. Set the oversteering (1) down over the
fixed bolts (3) on the machine. Next, screw the
nuts (2) securely.
2. Figure 4. Fit the support legs, using the
accompanying nut, spring and washer. See Figure
4.
Set the washer (5) down over the threaded pin (2)
and then the spring (4). Press the brush angle
support rod (1) down over the threaded pin and
screw on the nut (3) securely.
3. Figure 5. Fit the gear selector using the
accompanying bolt and nut.
Fit the gear selector (1) using the bolt (3) and nut
(2).
When fitting the gear selector when the machine is
new, bolt hole no. 1 on the gear fitting must be
selected. When the machine has operated for 100
hours or you feel that the speed is waning, change
to bolt hole no. 2.
4. Figure 6. Fit the brushes on the brush shaft (1).
When the brush is pushed in over the shaft (2), fit
the outer metal cups (4) and secure all of it with
the accompanying nuts (5).
modello effettivo può variano dall'illustrazione mostrata - Il modello effettivo può variare dalle illustrazioni mostrate
Ihr Modello Kann von der Abbildung abweichen - Tuo modello attuale puo essere diverso dalle illustrazioni

Operation

Before use, the following engine instructions
for readying the engine must be followed.
Before use, remove all foreign bodies from the area.
Stone, glass, branches and similar can damage the
sweeper. At the same time, check that the bolts on the
sweeper are secure.
Check the oil level in the engine before
starting. See the attached guide.
Starting the engine:
1. If the engine is cold, open the choke.
NB: If the engine is warm, the choke is not
necessary.
2. Open for full power, i.e. set the throttle handle
" "
to start .
3. Carefully pull the recoil start until you feel
resistance. Next, pull strongly on the recoil to
start the engine. Carefully let the recoil start
cord move back to the start position.
4. Regulate the choke until the engine runs
evenly.
Electrical starter (Only 800E/1000E models)
Illustration: 14
To avoid unintentionally starting the machine, the
start button should be removed from the machine
and stored safely when the machine is not in use.
1. By cold engine set the choke lever on "Choke" - By
warm engine set the choke lever on "Run"
2. Move the throttle lever to full "Rabbit" (A)
3. Hold the handlebar for the engine brake; this will
release the engine brake.
4. When starting the machine, insert the start button
in the ignition lock below the handlebar and push
in.
5. Hold the button (B) in until the engine starts and
then release.
6. Adjust the throttle lever if necessary and return the
choke lever in the "run" position. (only cold engine)
7. Hold the bar for self-propelled in order to start
mowing.
Electrical starter wire: (Only 800E/1000E models)
Illustration: 15-16-17
To make sure electrical wire not get squeezed, it´s
important that it´s mounted safely and properly
under the steering
1.Click the two electric wire ends together
2.Lead the wire under steering.
3.Insert zip ties into below steering holes and fasten.
16