Safety Warnings; Additional Safety Instructions - Makita UX01G Betriebsanleitung

KR401MP
EE400MP
EJ400MP
EJ400MP + LE400MP
BR400MP
SW400MP
UB400MP
UB401MP
UB402MP
PF400MP
NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and
may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures to protect the operator that are based on an estimation
of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the
times when the tool is switched off and when it is running idle in addition to the trigger time).
Declarations of Conformity
For European countries only
The Declarations of conformity are included in Annex A
to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings
WARNING
Read all safety warnings, instruc-
tions, illustrations and specifications provided with
this power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious
injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

Additional safety instructions

Personal protective equipment
► Fig.1
1. Wear safety helmet, protective goggles and
protective gloves to protect yourself from
flying debris or falling objects.
2. Wear ear protection such as ear muffs to pre-
vent hearing loss.
Attachment Left handle (Front grip) Right handle (Rear grip)
2
ah (m/s ) Uncertainty
2
K (m/s )
2.5 or less 1.5
2.5 or less 1.5
3.5 1.5
4.8 1.5
2.5 or less 1.5
2.5 1.5
4.6 1.5
2.5 or less 1.7
2.5 or less 1.5
2.5 or less 1.5
Wear proper clothing and shoes for safe
3.
operation, such as a work overall and sturdy,
non-slip shoes. Do not wear loose clothing or
jewelry. Loose clothes, jewelry or long hair can be
caught in moving parts.
4. When touching the cutting blade, wear protective
gloves. Cutting blades can cut bare hands severely.
Work area safety
1. Before operation, examine the work area for
stones or other solid objects. They can be
thrown or cause dangerous kickback and result in
serious injury and/or property damage.
Electrical and battery safety
1. Avoid dangerous environment. Don't use the
tool in dump or wet locations or expose it to
rain. Water entering the tool will increase the risk
of electric shock.
2. Do not dispose of the battery(ies) in a fire.
The cell may explode. Check with local codes for
possible special disposal instructions.
3. Do not open or mutilate the battery(ies). Released
electrolyte is corrosive and may cause damage to
the eyes or skin. It may be toxic if swallowed.
4. Do not charge battery in rain, or in wet locations.
5. Do not replace the battery with wet hands.
Do not replace the battery in the rain.
6.
7. Do not wet the terminal of battery with liquid
such as water, or submerge the battery. Do not
leave the battery in the rain, nor charge, use,
or store the battery in a damp or wet place. If
the terminal gets wet or liquid enters inside of bat-
tery, the battery may be short circuited and there is
a risk of overheat, fire, or explosion.
11 ENGLISH
Applicable
2
ah (m/s ) Uncertainty
2
K (m/s )
2.5 or less 1.5
2.5 or less 1.5
3.9 1.5
(ISO11806-1)
2.6 1.5
(ISO11806-1)
2.5 or less 1.5 EN60335-2-72
2.5 or less 1.5 EN60335-2-72
2.5 or less 2.5 EN50636-2-100
2.5 or less 1.5 EN50636-2-100
2.5 or less 1.5 EN50636-2-100
2.5 or less 1.5
standard
EN709
ISO11789
ISO22867
ISO22867
ISO22867