Safety Warnings; Additional Safety Instructions; Operation - Makita UX01G Betriebsanleitung

WARNING:
The vibration emission during actual use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures to protect the operator that are based on an estimation
of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the
times when the tool is switched off and when it is running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings
WARNING:
Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

Additional safety instructions

Personal protective equipment
► Fig.1
Wear safety helmet, protective goggles and
1.
protective gloves to protect yourself from
flying debris or falling objects.
Wear ear protection such as ear muffs to pre-
2.
vent hearing loss.
3. Wear proper clothing and shoes for safe operation,
such as a work overall and sturdy, non-slip shoes.
Do not wear loose clothing or jewelry. Loose clothes,
jewelry or long hair can be caught in moving parts.
When touching the cutting blade, wear protective
4.
gloves. Cutting blades can cut bare hands severely.
Work area safety
Before operation, examine the work area for
1.
stones or other solid objects. They can be
thrown or cause dangerous kickback and result in
serious injury and/or property damage.
Electrical and battery safety
1. Avoid dangerous environment. Don't use the
tool in dump or wet locations or expose it to
rain. Water entering the tool will increase the risk
of electric shock.
2. Do not dispose of the battery(ies) in a fire.
The cell may explode. Check with local codes for
possible special disposal instructions.
3. Do not open or mutilate the battery(ies). Released
electrolyte is corrosive and may cause damage to
the eyes or skin. It may be toxic if swallowed.
4. Do not charge battery in rain, or in wet locations.
Do not replace the battery with wet hands.
5.
6. Do not replace the battery in the rain.
7. Do not wet the terminal of battery with liquid
such as water, or submerge the battery. Do not
leave the battery in the rain, nor charge, use,
or store the battery in a damp or wet place. If
the terminal gets wet or liquid enters inside of bat-
tery, the battery may be short circuited and there is
a risk of overheat, fire, or explosion.
After removing the battery from the tool or
8.
charger, be sure to attach the battery cover to
the battery and store it in a dry place.
9. If the battery cartridge gets wet, drain the
water inside and then wipe it with a dry cloth.
Dry the battery cartridge completely in a dry
place before use.
Putting into operation
1. The cutting tool has to be equipped with the
guard. Never run the tool with damaged guards
or without guards in place!
2. Make sure there are no electrical cables, water
pipes, gas pipes etc. that could cause a hazard
if damaged by use of the tool.

Operation

1. Always keep your hands, face, and clothes
away from the cutting tool when it is rotating.
Failure to do so may cause personal injury.
2. During operation, keep bystanders or animals
at least 15 m away from the tool. Stop the tool
as soon as someone approaches.
3. During operation, never stand on an unstable
or slippery surface or a steep slope. During
the cold season, beware of ice and snow and
always ensure secure footing.
4. Never work on a ladder or tree to avoid loss of
control.
5. When you leave the tool, even if it is a short
time, always remove the battery cartridge. The
unattended tool with the battery cartridge installed
may be used by unauthorized person and cause
serious accident.
6. Before starting the tool, be sure that the cut-
ting tool is not touching the ground and other
obstacles such as a tree.
7. Check the cutting attachment frequently
during operation for cracks or damages.
Before the inspection, remove the battery
cartridge and wait until the cutting attachment
stops completely. Replace damaged cutting
attachment immediately, even if it has only
superficial cracks.
10 ENGLISH