After Operation - Kress KG760E.9 Bedienungsanleitung

NOTE: Push the mulching-bag switch lever to open the
mulching outlet before fitting the grass collection bag.
Assembling the side-discharge chute (See Fig.
C1, C2)
Lift the Side-discharge cover to assemble the side-
discharge chute.
NOTE: Remember to remove the grass collection bag
firstly and then push the mulching-bag switch lever to
close the mulching outlet before assembly.
Installing & removing the battery pack (See Fig.
D1, D2)
Insert the safety key before installing battery pack(s).
NOTE: Depress the battery release button to release
battery pack(s) from your tool. After recharging, insert
the battery pack into tool's battery port until you hear
a "click". A simple push and slight pressure will be
sufficient.
Checking the power indicator light (See Fig. D3)
Press the switch button for battery indicator light and the
power indicator light will be on .
OPERATION
Starting and Stopping (See Fig. E1, E2)
Press the Safety lock-out button, then the pull Operating
bail to start. Release the operating bail to stop.
For starting, press both the Safety lock-out button and
the Operating bail at the same time.
NOTE: Place the Mulch-Bag lever in the bag position
after each use. (See Fig. B1)
Operating the self-propel system (See Fig. F)
Press the Safety lock-out button,then push the Self-
propel speed-control lever to operate.
NOTE: To activate self-propel, press both the Safety
lock-out button and the Self-propel speed-control lever at
the same time.
MULCHING MOWING TIPS
While mulching, your new mower is designed to cut the
grass clippings into small pieces and distribute them
back into the lawn. Under normal conditions, the mulched
grass will biodegrade quickly and deliver nutrients to the
lawn. Please review the following recommendations for
optimum mulching performance.
1) Avoid mowing when the grass is wet from rain or dew.
Wet grass may form clumps which interfere with the
mulching action and reduce the runtime. The best
time to mow the grass is in the late afternoon when
the grass is dry and the newly cut area will not be
exposed to direct sunlight.
2) For the best mulching performance, set the cutting
height to remove about one third of the grass blade
length, ideally no more than 40mm at one time. If the
lawn is overgrown, it may be necessary to increase
the cutting height to reduce the pushing effort and
prevent overloading the motor. For extremely heavy
mulching, it is advisable to first cut at a high cut
height setting, and then re-cut to the final cut height.
Otherwise, make narrower cuts and mow slowly.
3) For the best performance, keep the mower housing
free of built-up grass. From time to time turn off
mower and wait for the blades to come to a complete
stop. Then unplug the safety key, remove the batteries
and turn mower on its side. Using an object such as a
stick, wipe out any accumulation of grass around the
blade area. Be careful of the sharp edges of the blade.
Ensure to clean the blade area often when cutting
wet or new grass and every time after the machine is
used.
4) Certain types of grass or grass conditions may
require that an area be mulched a second time to
fully disperse the grass throughout the lawn. If cutting
a second time, it is advisable to cut perpendicular
(across) the first cut pattern. DO NOT CHANGE
CUT PATTERN IN ANY WAY THAT WOULD CAUSE
MOWING DOWN A HILL.
5) Change your cutting pattern from week to week. This
will help prevent matting and graining of the lawn.
6) Do not mow on a slope that has an angle of greater
than 15
o
CUTTING AREA
The cutting area can be affected by several factors, such
as cutting height, lawn humidity, grass length and density.
Besides, starting and stopping the mower too many times
during operation will reduce the cutting area.
It is ideal for mowing up to 2000m² lot sizes.
TIPS:
1) It is recommended to mow your lawn more frequently,
walk at normal pace, and not to start/stop the mower
too often during operation.
2) For best performance, please ensure use two fully
charged battery packs at the same time and always
cut off 1/3 or less of the grass height.
3) Walk slowly when cutting long grass, so as to have
more effective cutting and properly discharge the
clippings.
4) Avoid cutting wet grass, otherwise it will stick to the
underside of the deck and the clippings cannot be
collected or discharged properly.
5) A higher cutting height shall be applied to new or
thick grass and it will extend the battery duration.
Adjusting the cutting height (See Fig. G)
Press and hold Cutting-height adjustment lever. Adjust
the cutting height up and down.
WARNING! Stop, release operating bail and wait
until the motor stops before adjusting height. The
blades continue to rotate after the machine is switched
off, a rotating blade can cause injury. Do not touch
rotating blades.
Opening the Led headlight (See Fig. H)
Press the switch button for Led headlight.
Removing/emptying grass collection bag (See
Fig. I1, I2)
WARNING! Always check the safety flap close the
discharge outlet before using. Never lift the safety
flap when the lawn mower is being used without fitted
grass collection bag.

AFTER OPERATION:

STORAGE (See Fig.J1, J2)
13
EN