Replacing The Blade; Ordering Replacement Parts; Storage And Transport - EINHELL GE-CM 18/32 Li Originalbetriebsanleitung

cleaning agents or solvents; these could
attack the plastic parts of the equipment. En-
sure that no water can seep into the device.
•
For best results, clean the lawn mower with a
brush or rag.
7.2 Maintenance
•
Worn out or damaged blades, blade mounts,
and bolts should be replaced as a set by an
authorized professional in order to keep the
equipment in balance.
•
Ensure that all mounting components (i.e.
screws, bolts, nuts etc.) are always tightened
so that the equipment can be safely operated
at all times.
•
Frequently check the grass catch assembly
for signs of wear.
•
Replace excessively worn or damaged parts
immediately.
•
In order to ensure that you enjoy the equip-
ment for many years to come, all screwed
parts, as well as the wheels and axles, should
be cleaned and lubricated.
•
Keeping your lawn mower in good condition
not only ensures a long lifespan and high per-
formance, but also enables the equipment to
thoroughly cut your grass with minimal effort.
•
The blade is subjected to more wear and
tear than any other component. Therefore,
routinely check the condition of the blade
and make sure that it is tightly fastened. If the
blade is completely worn out, it must be im-
mediately replaced or ground sharp again. An
excessively vibrating mower means that the
blade is not properly balanced or has become
deformed from striking an object. In this case,
the blade must be repaired or replaced.
•
There are no parts inside the equipment
which require additional maintenance.

7.3 Replacing the blade

Remove the rechargeable battery/batteries. For
safety reasons, we recommend having the blade
replaced by an authorized professional. Impor-
tant! Wear work gloves! Only replace the blade
with a genuine Einhell replacement blade, as this
will ensure top performance and safety under all
conditions.
Carry out the following steps to change the blade:
1. Undo the fastening screw (see Fig. 11).
2. Remove the blade and replace with a new
one.
3. When fi tting the blade, make sure it is ins-
talled in the right direction. The blade's air va-
Anl_GE_CM_18_32_Li_SPK9.indb 24 Anl_GE_CM_18_32_Li_SPK9.indb 24
GB
nes must project into the motor compartment
(see Fig. 11). The dome mounts provided
on the equipment must be aligned with the
punch holes provided in the blade (see Fig.
12).
4. Then retighten the fastening screw with a
wrench. The tightening torque should be ap-
prox. 25 Nm.
At the end of the season, perform a general ins-
pection of the lawn mower and remove any grass
and dirt which may have accumulated. At the start
of each season, ensure that you check the condi-
tion of the blade. If repairs are necessary, please
contact our customer service center. Use only
genuine spare parts.

7.4 Ordering replacement parts:

Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
Spare blade art. no.: 34.054.53

8. Storage and transport

Remove the rechargeable battery/batteries.
Storage
Store the equipment and accessories out of
children's reach in a dark and dry place at above
freezing temperature. The ideal storage tempera-
ture is between 5 and 30 °C. Store the machine in
its original packaging.
Transport
•
Fit the shipping protectors, if any.
•
For easier transport and/or storage, open the
wing nuts (Fig. 3b / Item 13) far enough to
allow the push bars to be flipped together at
this point. Take care not to damage the cable
and the push bar tubes.
•
Protect the machine from damage and the
strong vibrations that can occur particularly
when transporting in vehicles.
•
Secure the machine against slipping and tip-
ping over.
- 24 -
14.03.2023 10:38:49 14.03.2023 10:38:49