Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Confirming the Charging Current
Make sure to know the maximum charging current of the battery before charging, never use excessive current to charge to
damage your battery, which will result in over heat even explosion during the charging process. The charging and discharging
rate of battery is usually marked with C value. Multiplying the charging C value and battery capacity equals to the maximum
charging current supported by the battery. For example, for a 5000 mAh battery with a charging rate of 1C, the maximum
charging current would be 5000*1= 5000 mA; therefore, the maximum charging current is 5A.
For a lithium battery, if it is impossible to confirm the supported charging C value, please set the charging current below 1C, for
the sake of its (lithium battery) safety (the same applies to NiMH/NiCd batteries; no more than 0.1C for Pb batteries).
Battery Standard Parameters
LiPo
Nominal
3.7 V/cell
Voltage
Max. Charge
4.2 V/cell
Voltage
Storage
3.8 V/cell
Voltage
Min.
Discharge
3.0 V/cell
Voltage
Max. Charge
≤1C or
Current
more**
*) Sealed (gas tight) gel PB batteries up to 2.27-2.30 V/cell. Classic lead-acid („car battery") and valve-regulated lead-acid batteries
up to 2.46 V/cell.
**) Some LiPo batteries may be charged at 5C or even higher rate – always follow the battery manufacturer's recommendation.
TASK SETTINGS
Power on the charger and connect a battery; the charger will enter into the standby page. Short press the roller wheel to
activate the program setting menu Program setting menu. The items in this menu are as follows:
Charging Channel: This setting is convenient for charging multiple identical batteries (same type and number of cells, same
capacity). You can select the channel to be started. Red indicates selected, and gray indicates not selected.
For example: When identical batteries are connected to the both two channels, you can set both 1 and 2 to red; the charger will
charge both packs simultaneously with the same setting.
Note: If the batteries are not identical (same type and number of cells, same capacity) you to select the corresponding channel
to set and start the charging separately for each battery.
Connecting the Battery
Connect the charging leads to the respective XT60 output socket (CH1 or CH2) observing the correct polarity: (+) red cable, (-)
black cable. For lithium packs, it is highly recommended to ALWAYS connect the balance leads and utilize balanced charging to
ensure that the charger can accurately monitor the voltage of each cell.
LiIon
LiFe
3.6 V/cell
3.3 V/cell
4.1 V/cell
3.6 V/cell
3.7 V/cell
3.3 V/cell
3.0 V/cell
2.8 V/cell
≤1C
≤4-5C (A123)
LiHV
NiCd
3,7 V/cell
1.2 V/cell
4,35 V/cell
1.5 V/cell
Store fully
3,9 V/ cell
discharged
3,1 V/ cell
0.8 V/cell
≤1C
1-2C
Battery
Battery Type Selection
Cells
Select number of cells in the battery pack
Working Mode: Charge, Discharge, Storage
Mode
(lithium batteries only)
Select desired charge/discharge current:
Current
0.1-10.0 A
TVC
Terminal voltage control setting
Allows simultaneous charging of identical
Charge Channel
pack in both two channels
Start
Start charging/discharging program
Back
Return to previous screen or function
4
NiMH
Pb
1.2 V/cell
2.0 V/cell
1.5 V/cell
Type specific*
Store fully
Store fully
charged
charged
1.0 V/cell
1.8 V/cell
1-2C
≤0.4C
Werbung
