First Time Use - Bauknecht BT 1090 BA Bedienungsanleitung

FIRST TIME USE

POWER MANAGEMENT
Some models are equipped with a power limiting function (Power
Management). This function allows the total power generated by the hob to
be set to different values selected by the user. To do this, for the first minute
after having connected the hob to the power supply, it is possible to access
the power limiting menu.
1. Press the (11) touch key for three seconds. The letter PL will appear on
the timer indicator (12)
2. Press the locking touch key
the hob can be limited will appear and these can be changed using the
(11) and (10) sensors.
3. Once the value has been selected, once again press the locking touch key
(6).The hob will be limited to the chosen power value.
The power levels available are:
2 kW - 2.5 kW - 3 kW - 3.5 kW - 4 kW - 4.5 kW - 5 kW - 5.5 kW - 6 kW - 6.5 kW - 7 kW
If you want to change the value again, you must unplug the hob and plug it
in again after a few seconds. Thus you will again be able to enter the power
limiting menu.
Every time the power level of a hotplate is changed, the power limiter will
calculate the total power the hob is generating. If you have reached the total
power limit, the touch control will not allow you to increase the power level
of that hotplate. The hob will beep and the power indicator (3) will blink at
the level that cannot be exceeded. If you wish to exceed that value, you must
lower the power of the other hotplates. Sometimes it will not be enough to
lower another by a single level as this depends on the power of each hotplate
and the level it is set at.
It is possible that to raise the level of a large hot plate that of several smaller
ones must be turned down.
If you use the quick switch-on at maximum power function and the said
value is above the value set by the limit, the hotplate will be set to the
maximum possible level. The hob will beep and the said power value will
blink twice on the indicator (3).
To set the power of the hob:
Only visible while running.
The manoeuvres are done by means of the touch keys. You do not need
to exert force on the desired touch key, you only need to touch it with
your fingertip to activate the required function
Each action is verified by a beep.
Use the cursor slider (2) to adjust power levels (0 - 9) by sliding your
finger over it. Sliding towards the right increases the value, whereas
sliding towards the left decreases it.
It's also possible to directly select a power level by placing your finger
directly on a desired point of the cursor slider (2)
In order to select a plate on these models, directly touch the cursor
slider (2).
SWITCHING ON THE DEVICE
1 Touch the On touch key
will become active, a beep will be heard and the indicators (3) will light up
displaying a "-". If any cooking area is hot, the related indicator will flash an H.
If you do not take any action in the next 10 seconds the touch control will
switch off automatically. When the touch control is activated, you can
disconnect it at any time by touching the touch button
been locked (lock function activated). The touch button
priority to disconnect the touch control.
(6). The different power values to which
(1) for at least one second. The touch control
(1), even if it has
ACTIVATING PLATES
Once the Touch Control is activated with sensor
be turned on by following these steps:
1. Slide the finger or touch in any position of one of the cursors "slider"
(2). The zone has been selected and simultaneously the power level
will be set between 0 and 9. That power value will be shown on the
corresponding power indicator and its decimal dot (4) will keep light up
during 10 seconds.
2. Use the cursor slider (2) to choose a new cooking level between 0 and
9.
As long as the plate is selected, in other words, with the decimal (4) dot
light up, its power level can be modified.
TURNING OFF A PLATE
Using the touch slider key (2) lower the power to level 0. The hotplate
will switch off.
When a hot plate is switched off an H will appear in its power indicator
(3), if the glass surface of the related to the cooking area is hot and there
is a risk of burns. When the temperature drops, the indicator (3) switches
off (if the hob is disconnected), or otherwise a "-" will light up if the hob
is still connected.
TURNING ALL PLATES OFF
All plates can be simultaneously disconnected by using the general on/
off sensor (1). All plate indicators (3) will turn off. If the heating zone
turned off is hot, its indicator shows an H.
(1) always has
EN
(1), any plate can