Product Description And Specifications; Intended Use; Product Features; Noise/Vibration Information - Bosch GSH 27 VC Professional Originalbetriebsanleitung

cessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make ex-
posed metal parts of the power tool "live" and could give
the operator an electric shock.
Additional Safety Instructions
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Do not touch any application tools or adjacent housing
u
components shortly after operation. These can become
very hot during operation and cause burns.
Take care when carrying out demolition work using
u
the chisel. Falling fragments of the demolition material
could injure you or any bystanders.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.

Intended use

The machine is intended for heavy chiselling and demolition
work as well as for driving in and compacting with the appro-
priate accessories.

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
Bosch Power Tools
(1) On/off switch
(2) Handle (insulated gripping surface)
(3) Tool retainer
(4) Tool holder
(5) Tool shank
(6) Shoulder
Technical Data
Demolition hammer
Article number
Rated power input
Impact rate
Impact energy per stroke
according to EPTA-Proced-
ure 05:2016
Tool holder
Weight according to EPTA-
Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
The appliance meets IEC 61000-3-11 requirements and is
subject to conditional connection. The appliance can lead to
occasional voltage fluctuations under unfavorable power
conditions. The impedance of this appliance is set as Z
= 0.30 Ω. The user must make sure, that the connection
point, with the impedance Z , on which the appliance shall
max
be plugged in meets the impedance requirement: Z
≥ Z . If Z is unknown, determine Z
tual max max
with the network supplier or supply authority.

Noise/Vibration Information

Noise emission values determined according to
EN IEC 62841-2-6.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 92 dB(A); sound power level
103 dB(A). Uncertainty K=3 dB.
Wear hearing protection
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN IEC 62841-2-6:
2
Chiselling: a = 9.7 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
English | 11
GSH 27 VC
3 611 C0A 0..
W 2000
–1
min 920
J 62
mm 28
" 1 ⅛
kg 29.1
/ II
actual
ac-
in consultation
max
2
1 609 92A 7ES | (10.11.2022)