Product Description And Specifications - Bosch GSH 5 CE Professional Originalbetriebsanleitung

Keep cutting tools sharp and clean. Properly main-
u
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
u
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
u
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Hammer Safety Warnings
Safety instructions for all operations
Wear ear protectors. Exposure to noise can cause hear-
u
ing loss.
Use auxiliary handle(s), if supplied with the tool. Loss
u
of control can cause personal injury.
Hold the power tool by insulated gripping surfaces,
u
when performing an operation where the cutting ac-
cessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make ex-
posed metal parts of the power tool "live" and could give
the operator an electric shock.
Additional Safety Instructions
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Do not touch any application tools or adjacent housing
u
components shortly after operation. These can become
very hot during operation and cause burns.
Take care when carrying out demolition work using
u
the chisel. Falling fragments of the demolition material
could injure you or any bystanders.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
Bosch Power Tools
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for chiselling work in concrete,
brick, stone and asphalt, as well as for driving in and com-
pressing with the appropriate accessories.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Dust protection cap
(2) Locking sleeve
(3) Chisel adjustment ring (Vario-Lock)
(4) Vibration damping
(5) Handle (insulated gripping surface)
(6) On/off switch
(7) Thumbwheel for impact rate preselection
(8) Service indicator
(9) Stand by Indicator
(10) Auxiliary handle (insulated gripping surface)
(11) Knurled nut for auxiliary handle
Technical Data
Demolition hammer
Article number
Rated power input
Impact rate
Impact energy per stroke
according to EPTA-Proced-
ure 05:2016
Chisel positions
Tool holder
Weight according to EPTA-
Procedure 01:2014
English | 11
GSH 5 CE
3 611 C21 0..
W 1150
–1
min 1510–2870
J 8.3
12
SDS max
kg 6.1
1 609 92A 744 | (07.11.2022)