Inhaltsverzeichnis
Werbung
MANUAL AND THE APPLICABLE LAW, THE LATTER
PREVAILS.
Regulatory Information
These clauses apply only to the products bearing the
corresponding mark or information.
EU/UKCA Conformity Statement
This product and - if applicable - the
supplied accessories too are marked
with "CE" and comply therefore with the
applicable harmonized European
standards listed under the EMC Directive 2014/30/EU,
the LVD Directive 2014/35/EU, the RoHS Directive
2011/65/EU, the ATEX Directive 2014/34/EU.
This product and - if applicable - the
supplied accessories too are marked with
"UKCA" and comply therefore with the
following directives: Electromagnetic
Compatibility Regulations 2016, Electrical Equipment
(Safety) Regulations 2016, the Restriction of the Use
of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations UKSI 2016:2017.
2012/19/EU (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste
in the European Union. For proper
recycling, return this product to your local
supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info
According to the Waste Electrical and Electronic
Equipment Regulations 2013: Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the United Kingdom. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information see: www.recyclethis.info.
Intended use of the camera
ATEX:
II 2 G Ex db IIC T6 Gb
II 2 D Ex tb IIIC T80°C Db
IECEx: Ex db IIC T6 Gb/ Ex tb IIIC T80 °C Db
Hazardous Area Classification: Zone 1, Zone 2, Zone
21, Zone 22.
IP Degree: IP66/IP68 (2 m, 2 h)
Ex Standards:
IEC 60079-0: 2017
IEC 60079-1: 2014
IEC 60079-31: 2013
Nameplate:
Special Conditions for Safe Use:
1. Under certain extreme dust circumstances, the
coating film on the enclosure of this equipment may
generate an ignition-capable level of electrostatic
charge. Therefore the equipment shall not be installed
in a location where the external conditions are
conducive to the build-up of electrostatic charge on
such surfaces. In addition, the equipment shall only be
EN 60079-0: 2018
EN 60079-1: 2014
EN 60079-31: 2014
cleaned with a damp cloth.
2. Specific guidance noted to contact the original
manufacturer for information on the dimension of the
flameproof joints.
3. The fasteners of window cover shall only be
replaced with the identical part No.
SC-HSCSM6X15L11-SUS316L-DAC.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-003 (A)/NMB-003(A)
standards requirements.
Warning:
This is a class A product. In a domestic environment
this product may cause radio interference in which
case the user may be required to take adequate
measures.
KC
A 급 기기: 이 기기는 업무용(A 급)
전자파적합기기로써 판매자 또는 사용자는 이
점을 주의하시기바라며, 가정 외의 지역에서
사용하는 것을 목적으로 합니다.
Safety Instructions
These instructions are intended to ensure that user
can use the product correctly to avoid danger or
property loss.
Laws and Regulations
In the use of the product, you must be in strict
compliance with the electrical safety regulations of
the nation and region.
Transportation
Keep the device in original or similar packaging while
transporting it.
Keep all wrappers after unpacking them for future
use. In case of any failure occurred, you need to
return the device to the factory with the original
wrapper.
Transportation without the original wrapper may
result in damage on the device and the company shall
not take any responsibilities.
Do not drop the product or subject it to physical
shock. Keep the device away from magnetic interface.
Power Supply
Input voltage should meet the Limited Power Source
(100 to 240 VAC) according to the IEC62368 standard.
Please refer to technical specifications for detailed
information.
Make sure the plug is properly connected to the
power socket.
The socket-outlet shall be installed near the
equipment and shall be easily accessible.
DO NOT connect multiple devices to one power
adapter, to avoid over-heating or fire hazards caused
by overload.
DO NOT touch the bare metal contacts of the inlets
after the circuit breaker is turned off. Electricity still
exists.
+ identifies the positive terminal(s) of equipment
which is used with, or generates direct current. -
identifies the negative terminal(s) of equipment
which is used with, or generates direct current.
The equipment must be connected to an earthed
mains socket-outlet.
A readily accessible disconnect device shall be
incorporated external to the equipment.
An all-pole mains switch shall be incorporated in the
electrical installation of the building.
Ensure correct wiring of the terminals for connection
to an AC mains supply.
The equipment has been designed, when required,
modified for connection to an IT power distribution
system.
Use the power adapter provided by qualified
manufacturer. Refer to the product specification for
detailed power requirements.
Installation
Never place the equipment in an unstable location.
The equipment may fall, causing serious personal
4
Werbung
Inhaltsverzeichnis
