ripcurl Funktion. Dualzeit mit Timer, Chronograph, Wecker und Licht Bedienungsanleitung Seite 3

English
Function. Dual Time with Timer, Chronograph, Alarm & Light
sound icon ( )will show on-screen in Time
mode.
To Set Timer
1. In TIME 1 mode, push MODE twice to enter
Timer mode.
2. Hold LIGHT for 2 seconds. Once Timer setting
is flashing, push START/STOP or LAP/RESET to
select setting – "CD-STP" for Countdown-Stop;
"CD-REP" for Countdown-Repeat; or "CD-UP" for
Countdown-Up.
3. Push MODE to set the Hour. Once flashing,
push or hold START/STOP and LAP/RESET to
increase or decrease the Hour.
4. Repeat to advance through and set Minutes
and Seconds.
5. Push LIGHT to finish the setting.
Functions
Auto Light Function
In TIME 1 mode, hold LIGHT for 2 seconds, then
push START/STOP or LAP/RESET to toggle Light
on or o . If auto light function is ON, the whole
screen will light up and stay on for 3 seconds if
any key is pressed. If Auto Light is OFF, in and
mode, push LIGHT to light up the digital display
screen for 3 seconds.
Hourly Chime Function
1. In TIME 1 mode, hold LIGHT for 2 seconds.
2. Push MODE once to enter Chime setting.
3. Use START/STOP or LAP/RESET buttons to
toggle Chime on or o . When on, your watch will
chime on the hour, every hour.
Tip: when the Chime is enabled, a bell icon will
show on-screen in Time mode.
Button Key Tone Function
The Button Key Tones can be disabled. In TIME 1
mode, push LAP/RESET to toggle Key Tones on
or o . When on, "KEY" will show on-screen in
Time mode, above the Minutes display.
Chronograph Function
1. In TIME 1 mode, push MODE once to enter the
Chronograph mode.
2. Push START/STOP to start the Chronograph.
Tip: when the Chronograph is running, a stop-
watch icon will show on-screen.
3. Push START/STOP to stop the Chronograph.
4. Hold LAP/RESET to reset the Chronograph to
zero.
Tip: to view the current time and date while the
Chronograph is running, push MODE 3 times.
The stopwatch icon (
indicate that the Chronograph is still running.
Chronograph Lap Function
1. While the chronograph is running, push
LAP/RESET to stop the Chronograph's first lap.
The Chronograph will restart after several
seconds.
2. To recall previous lap memory, push LIGHT
while the Chronograph is stopped. Push again
and the next lap will display. Push START/STOP
or LAP/RESET button to exit and return to the
Chronograph mode.
Tip: there are a total of 10 lap memories. "LAP L"
will be shown if lap number is larger than 9. The
"LAP L" memory will be overwritten by the latest
lap. The first 9 laps will be kept unchanged.
Timer Function
1. Follow instructions above to pre-set Timer to
desired time.
2. In TIME 1 mode, push MODE twice to enter
Timer mode.
3. Push START/STOP to start the Timer.
Tip: when the Timer is running, an arrow icon ( )
will appear on-screen.
4. Push START/STOP to stop the Timer.
Tip: to view the current time and date while the
Timer is running, push MODE twice. The arrow
icon ( ) will show to indicate that the Timer is
still running.
Tip: a Chime will sound for 30 seconds if the
Timer is counted down to zero. If the pre-set time
is less than 1 minute, and Countdown-Repeat is
selected, a Chime will sound for 1 second each
time the Timer is counted down to zero. The
Timer will stop and reset automatically with a
Chime for 30 seconds, if it is counted up to the
maximum (23 hours, 59 minutes, 59 seconds).
) will show on-screen to