Husqvarna Aspire LC34-P4A Bedienungsanweisung Seite 21

• Put tape on the battery connectors and make
sure that the battery cannot move around during
transport.
• Attach the product during transport.
Storage
• Before storage, let the product become cool.
• Always remove the battery for storage.
• To prevent accidents, make sure that the battery is
not connected to the product during storage.
• Keep the battery charger in a closed and dry space.
• Keep the battery and the battery charger in a dry
space where there is no moisture or frost.
• Disconnect the battery from the battery charger
during storage.
• Do not keep the battery where static electricity can
occur. Do not keep the battery in a metal box.
• Keep the product where the ambient temperature is
between -20 °C and +50 °C.
• Keep the battery where the ambient temperature is
between -20 °C and +50 °C and out of sunlight.
• Store the battery charger in a dry, enclosed and
frost-free place.
• Make sure that the battery is clean and charged
before you put it in storage for long periods.
• Keep the product, battery and battery charger in
a locked area out of reach for children and not
approved persons.
• Clean the product and make sure that the grass
catcher is empty.
• Do the maintenance procedures given in this
operator's manual. Refer to
17 .
• Do a complete servicing before you put the product
in storage for a long time.
To set the product in storage position
WARNING:
during transport and storage turn the safety
key to 0, remove the battery and wait a
minimum of 5 seconds.
1. Remove the battery.
2. Set the product in transport position. Refer to
the product in transport position on page 20 .
3. Move the product to the storage location.
To store the product horizontally on the
ground
1. Set the product in storage position. Refer to
the product in storage position on page 21 .
2. Attach the grass catcher. Refer to
grass catcher on page 21 .
3. Store the product horizontally on the ground. (Fig.
48)
1848 - 004 -
Maintenance on page
To prevent accidental start
To set
To set
To attach the
To store the product vertically on the ground
1. Set the product in storage position. Refer to
the product in storage position on page 21 .
2. Lift the product by the lifting points on the handle and
put the product vertically on level surface. (Fig. 49)
WARNING:
by the cutting cover. The blade is very
sharp and cuts can easily occur.
3. Attach the grass catcher. Refer to
grass catcher on page 21 .
4. Make sure that the product is stable and that the 2
support legs touch the floor.
5. Store the product vertically on the ground. (Fig. 50)
To store the product vertically on the supplied
hook
WARNING:
the wall with the supplied hook.
1. Install the supplied hook. Refer to
on the wall on page 14 .
2. Set the product in storage position. Refer to
the product in storage position on page 21 .
3. Lift the product by the lifting points on the handle.
(Fig. 49)
WARNING:
by the cutting cover. The blade is very
sharp and cuts can easily occur.
4. Hang the product vertically on the supplied hook.
To install the hook on the wall on page 14 .
Refer to
(Fig. 51)
5. Make sure that the product hangs correctly and is
stable on the 2 rods of the hook.
6. Attach the grass catcher. Refer to
grass catcher on page 21 .
To attach the grass catcher
1. Attach the grass catcher to the groove on the front of
the product. (Fig. 52)
2. Push the lower part of the grass catcher against the
lifting point until you hear a click. (Fig. 53)
Disposal
Symbols on the product or the packaging of the product
indicate that this product cannot be handled as domestic
waste. It must be submitted to an appropriate recycling
station for the recovery of electrical and electronic
equipment.
By ensuring that this product is taken care of correctly,
you can help to counteract the potential negative impact
on the environment and people that can otherwise
To set
Do not lift the product
To attach the
Only hang the product on
To install the hook
To set
Do not lift the product
To attach the
21