Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
5. Feed the trim line (5a) through the eyelet
on the sail (2c) and then through the mast
extension as shown in Figure M, then fix the
trim line (5a) by clamping it in the catch (5b)
(Fig. M).
Installing the wishbone boom
1. Open the locking lever (4b) of the wishbone
boom (4) and attach the wishbone boom to
the mast (3) (Fig. N).
2. Attach the rope (4c), as shown in Figure N,
and clamp it with the clamping device (4d).
3. Run the rope (4e) through the eye (2d) and fix
it, as shown in Figure O.
Attaching the rig to the board
1. Turn the mast stand (6) into the screwing
device (1c) (Fig. P).
2. Attach the rubber loop (4g) of the rudder
(4a) to the mast extension (5), as shown in
Figure Q.
3. Fold the mast base (6) to one side. Press the
button (5c) on the mast extension and attach
the mast extension (5) to the power joint (6a)
(Fig. R).
Note: proceed with the dismantling of the rig in
the reverse order.
Attaching the leash to the product
(Fig. T)
Attach the leash (19) to the rear D-Ring (1k) as
shown in Figure T.
1. Pull the loop (19b) of the leash through the
D-Ring (1k).
2. Pull the ankle attachment (19a) through the
loop (19b) of the leash until there is a knot on
the D-Ring.
Using the leash (Fig. U)
WARNING!
• Never attach the leash (19) to your ankle
when you are using the product on flowing
bodies of water (e.g. bodies of water with
rapids and rivers).
• Never attach the leash to your ankle in off-
shore winds.
• When using the product in deep waters,
always affix the leash (19) to your ankle, as
shown in Figure U.
Transportation
Backpack
You can transport or store the board in a
backpack (13). Disassemble the product as
described in the section 'Deflating'. Ensure that
the product is completely clean and dry.
1. Place the board on a clean, even and dry
surface.
2. Roll the board together and insert it into the
backpack.
Carry-case
You can transport or store the mast, sail and
paddle in the carry-case (15). Disassemble the
mast, sail and paddle. Ensure that the product is
completely clean and dry.
Case
You can transport or store the wishbone boom in
the case (14). Disassemble the wishbone boom.
Ensure that the product is completely clean and
dry.
12
GB
Dry sack
A splash-proof dry sack (20) comes with the
product. Smaller objects can be kept in the dry
sack.
Note: the dry sack is not waterproof. Do not
store any sensitive items, such as cameras, in the
dry sack.
Care, storage, repairs and
maintenance
Care
WARNING!
Do not use harsh cleaning agents, brushes with
metal or nylon bristles, or any sharp or metallic
objects such as knives, or similar. Only use mild
cleaning agents. Clean the board only when the
valve is closed, and after every use.
1. Remove the US fin and the centreboard from
the board.
2. Place the board on a clean, even and dry
surface.
3. Clean the board and fins with fresh water
and mild soap in order to remove any salt
crystals, grains of sand and any other minor
contamination.
4. Wipe everything down with a soft, dry cloth.
5. Let the board and fins dry completely
afterwards.
Storage
WARNING!
Mould may form if the product is not stored
properly.
• Store the product in a clean, dry, well-
ventilated location away from direct sunlight,
where it is not exposed to major temperature
fluctuations.
• When not in use for an extended period, we
recommend that you disassemble the product
completely and store it in the backpack
provided.
• Store the product in a safe place, out of reach
of children.
• Do not place heavy or sharp objects on the
product.
• After an extended storage period, check the
product for wear and tear, or signs of ageing.
Repairs
WARNING!
Before every use, check the board for pressure
loss, holes or tears. If the board is leaking air,
this could be due to a leaking valve, a defective
valve, or a leak in the board itself.
Under no circumstances should you attempt to
repair larger damaged areas yourself.
You can repair minor damage with the repair
patch provided (17).
Valve
To check whether the valve is leaking or
defective, proceed as follows:
1. Turn the valve cover (1h) anti-clockwise and
remove it from the valve (1i).
2. Ensure that there is no sand or other foreign
objects in the valve.
3. Fully inflate the board (1).
4. Close the valve.
5. Rinse the area of the board around the valve
with soapy water.
If bubbles form around the valve,
the valve must either be tightened or
replaced.
• Tightening the valve (Fig. S):
1. Turn the valve cover (1h) anti-clockwise and
remove it from the valve (1i).
2. Place the valve key (16) on the valve until it
fully grips the valve.
3. Tighten the valve by turning the valve key
clockwise.
4. Close the valve with the valve cover and rinse
the area of the board around the valve with
soapy water.
If no more bubbles form, the valve is tightly
sealed.
• Replacing the valve (Fig. S):
If bubbles still form around the valve even after
tightening the valve, then it must be replaced.
1. Completely release the air from the board.
2. Turn the valve cover (1h) anti-clockwise and
remove it from the valve.
3. Place the valve key (16) on the valve until it
fully grips the valve.
4. Turn the valve key anti-clockwise until the
valve can be removed from the board.
5. Remove the defective valve from the board.
6. Insert a new valve into the board.
Note: you may order a replacement valve from
the customer service address below. For optimal
sealing, we recommend that you smear a little
silicone grease or Vaseline around the valve.
7. Place the valve key onto the valve and tighten
the valve by turning it clockwise.
8. Place the valve cover on the valve and tighten
it by turning it clockwise.
Leaks
Only repair leaks in the board with a suitable
adhesive. Adhesive is included in the package
contents. Repairs with unsuitable adhesive can
lead to further damage!
Suitable adhesives can be found in specialist
shops.
Note: small leaks (smaller than 2mm) can also
be repaired just using the adhesive by applying
it directly to the leaky area. Larger leaks (larger
than 2mm) can be repaired as follows:
1. Completely release the air from the board.
2. Thoroughly clean the area to be repaired.
3. Dry the cleaned area.
4. Cut a patch that is large enough to cover the
damaged area plus 1.5cm around it on all
sides.
5. Apply the adhesive to the leak and to the
patch itself. Allow the adhesive to dry for
approx. 2–4 minutes.
6. Firmly press the patch onto the leak with a soft
object. Make sure that you work on an even
surface without any creases or folds. Using a
rounded object, gently remove any bubbles,
moving outwards from the centre.
7. Let the adhesive dry for at least 12 hours after
the repair.
8. After the drying process is complete, add
more adhesive to the edges of the patch.
Werbung
Inhaltsverzeichnis
