Kärcher WPD 200 Basic Originalbetriebsanleitung Seite 20

1 Bracket
2 Plate
3 Filter
4 Handle
a Remove the filter.
b Insert filter
 Turn the filter to the left until the tab is visible.
 Pull the filter downwards out of the support and re-
move it.
Note:
The used filter can be disposed of as domestic waste af-
ter the water has been drained.
 Wear sterile gloves.
 Unpack the new filter.
 Turn the filter so that the handle is on the left side
and insert it into the relevant support from the bot-
tom.
 Turn the filter to the right all the way to the stop.
1 Bracket
2 Filter
 Check installation position.
The marking on the label on the support and on the
filter must be aligned with each other.
Note
If both filters are replaced at the same time, also replace
the other filter at this time. The subsequent rinse pro-
cess can be performed on both filters simultaneously.
Note:
Filters must be installed in the same position and
must not be interchanged! Observe marking!
 Close device door and insert drip pan.
 Place an receptacle underneath the water outlet.
 Set the appliance switch to "I".
 Open the water supply again.
 Place an receptacle underneath the water outlet.
20
 Operate the button for unchilled water.
The new filter is flushed.
 The maximum dispensing time is limited to 60 sec-
onds. To resume the rinsing process, press the
button for unchilled water again.
 Rinse the filter until the dispensed water is clear
and odour-free, however, at least with 20 litres.
 After every filter change the performance of a
chemical cleaning is recommended (see "chemical
cleaning").
Emptying the drip pan
As soon as the drip pan has reached its maximum filling
level, the LED of the button for unchilled water starts
flashing blue.
 Remove the drip pan.
 Empty the drip pan.
 Check drip pan for soiling and clean as necessary.
 Insert drip pan.
The device is ready for operation again.
The selection water types is shown on the display.
Emptying the can (option)
As soon as the can has reached its maximum filling lev-
el, the LED of the button for chilled water starts flashing
blue.
 Open the door on the support leg.
1 Cap with filling level sensor
2 Can
 Unscrew the locking cover.
 Remove cap with filling level sensor.
 Remove and empty can.
 Reinsert the can.
 Fit cap with filling level sensor and tighten.
 Close the door of the base.
All LEDs are blue.
The device is ready for operation again.
General information on handling CO
When replacing CO bottles, the safety instructions of
2
the gas supplier and any statutory regulations must be
observed.
 The CO bottle must be equipped with a pressure
2
reducer approved by Kärcher, so that the level of
carbonation of the water can be adjusted.
 The food gas carbon dioxide E 290 must comply
with the purity requirements as per directive 96/77/
EG and must be marked as per Art. 7 of the direc-
tive 89/107/EWG.
 Prior to using a gas bottle, one has to make sure
that the correct gas type has been provided. Only
the hazardous goods label, which must be present
on all gas bottles, can be considered reliable infor-
mation about the type of gas. The colour of the gas
bottle does not always provide clear information re-
garding the gas type. A gas bottle whose content is
questionable or which is abnormal in any other way
(damage, fire damage, signs of mechanical tam-
pering), must not be used.
 Please adher to country-specific regulations.
DANGER
Risk of explosion!
 Do not use CO bottle with riser. Riser bottles are,
2
for example, marked with a red warning label.
Mortal danger due to possibly bursting CO
 Install and fasten the pressure gas container in an
upright position.
 Never connect the pressure gas container without
pressure reducer and safety valve. The pressure
7
-
EN
reducer with safety valve must be approved for the
device type.
Risk of suffocation on account of escaping carbon diox-
ide.
 The installation room must be aerated and ventilat-
ed sufficiently or if a suitable gas warning system
must be installed.
 Do not expose the gas cylinder to direct sunlight.
The gas cylinder must be protected against exces-
sive heating.
 Attach visible marking that points out
the potential presence of gaseous CO
Replacing the CO
Prompt to replace the CO2 bottle:
WPD 200 Button for carbonated water deactivated
LED for carbonated water flashes
1 Rotating regulator
2 Pressure reducer
3 Union joint
4 Main tap
5 Pressure gauge control pressure
6 CO hose
2
 Open the door on the support leg.
 Close the gas bottle at the main tap.
 Turn the pressure regulator to 0.
 Unscrew the pressure reducer from the empty gas
bottle.
 Screw the protective cap onto the empty gas bottle.
 Loosen the tie down strap for securing the CO
tle.
 Remove the empty gas bottle.
 Insert the new gas bottle in the base and secure it
by means of the tie down strap.
 Unscrew the protective cap from the new gas bot-
tle.
 Briefly open the main tap so that possibly present,
liquid CO can escape.
2
 Screw the pressure reducer onto the new gas bot-
tle. Watch for correct mounting of the sealing ring!
 Slowly open the main tap on the gas bottle.
 Set 3 bar on the pressure reducer by means of the
control knob.
 Close the main tap on the gas bottle.
 Read the value indicated on the pressure gauge
bottles
control pressure.
2
 The indicated value must remain constant for at
least 5 minutes.
 With detectable pressure reduction:
Check if the O-ring between the gas cylinder and
the pressure reducer is present and free of dam-
age. Replace defective O-ring.
Check the correct positioning of the pressure re-
ducer.
Tighten covering nut firmly.
Check the hose coupling on the pressure reducer
and the CO hose for visible damage. In case of
2
doubt, call the Customer Service.
 If the pressure reduction cannot be remedied by
the stated measures, the pressure reducer is de-
fective and must be replaced.
 Open main tap.
 Set the operating pressure on the pressure reducer
by means of the control knob.
Connect the CO
approx. 3 bar (static) before dispensing water and
then check that the pressure is approx. 3.0 bar
when dispensing carbonated water (sparkling).
 Close the door of the base.
 Place an receptacle underneath the water outlet.
 After renewing the CO
sparkling water to refill the CO2 mixer.
gas tank.
2
.
2
bottle
2
bot-
2
-First set the pressure regulator to
2
bottle, dispense one litre of
2