Carromco 78155 Montageanleitung Seite 3

78155, 78156 – Scooter XT-200
HANDLEBARS
a) Insert the left and right handlebar ends into the T shaped top of the steering column. Ensure the spr Insert the left and right handlebar ends into the T shaped top of the steering column. Ensure the spring Insert the left and right handlebar ends into the T shaped top of the steering column. Ensure the spr
buttons of the retaining clips firmly locate into the recessed holes. buttons of the retaining clips firmly locate into the recessed holes.
b) To extend the handlebar column to one of the To extend the handlebar column to one of the four height positions, undo the quick release lever and pull
the handlebars upwards. The spring button will locate into the first recessed hole, to re
spring button while maintaining to pull ng button while maintaining to pull the handlebars in an upward direction. Ensure the quick release lever
is always firmly closed.
INSPECTION BEFORE RIDE
WARNING: Check and secure all fasteners before every ride. Make sure the steering tube clamps, steering Check and secure all fasteners before every ride. Make sure the steering tube clamps, steering Check and secure all fasteners before every ride. Make sure the steering tube clamps, steering
tube extension quick release, and handlebars spring button are locked properly in place before riding. Keep
your fingers clear of the pivoting mechanism when folding or u your fingers clear of the pivoting mechanism when folding or unfolding the scooter.
standing clear. Periodically the scooter should b eriodically the scooter should be checked for any undue wear to the wheels, hubs and
braking mechanism. All fixings should be checked for security. braking mechanism. All fixings should be checked for security.
COLLAR CLAMPS
Using the correct size Allen key, check the
item is tightened and quality inspected at the factory, but item is tightened and quality inspected at the factory, but there is a slight chance
that the effects of shipping or handling may have caused this bolt to loose. that the effects of shipping or handling may have caused this bolt to loose.
Warning: Failure to properly secure the quick-release lever may cause the T-tube Warning: Failure to properly secure the quick
to telescope up or down while riding which may cause you to lose control and fall. to telescope up or down while riding which may cause you to lose control
With the quick-release properly adjusted and engaged, the handlebars will not release properly adjusted and engaged, the handlebars will not
move up or down.
WHEELS, TIRES, WHEEL BEARINGS
Under normal circumstances and conditions, the wheels and wheel bearings are maintenance free. Under normal circumstances and conditions, the wheels and wheel bearings are maintenance free. Under normal circumstances and conditions, the wheels and wheel bearings are maintenance free.
Nonetheless, it is the responsibility of the owner or g
tear, the axle for proper tightness and proper tightness and wheel bearings for side-to-side play and loose parts. When a wheel or
wheel bearing develops play, this is an indication
immediately with only genuine wheels. Worn tires/ wheels/
wear-and-tear and are not covered by the Retailer Warranty. tear and are not covered by the Retailer Warranty.
The wheels and the axis bolt are fixed with screws, locking nuts, which do
for your safety, check the tightness of the screw-nuts before each use. If once loose, following a violent for your safety, check the tightness of the screw
impact, please contact the dealer for a review and tightening as the thread locking is necessary to ensure a impact, please contact the dealer for a review and tightening as the thr
perfect setting. The wheel bearings require no special maintenance (other than lubrication see
MAINTENANCE). When the wheel bearing
REPLACEMENT OF WHEELS
To change the wheels, loosen the axle fitting with 2 Allen keys and take the wheels off the axle. Allen key can To change the wheels, loosen the axle fitting with 2 Allen keys and take the wheels off the axle. Allen key can To change the wheels, loosen the axle fitting with 2 Allen keys and take the wheels off the axle. Allen key can
be used to push the bearings out of the wheel to use them in the new wheel. However, it is usually advisable be used to push the bearings out of the wheel to use them in the new wheel. However, it is usually advisable be used to push the bearings out of the wheel to use them in the new wheel. However, it is usually advisable
to change the bearings when the whe to change the bearings when the wheels are changed. Put the bearings into the new wheel with the bolt
spacer and mount them to the frame with the axle screws. Make sure the axle has been screwed on tightly spacer and mount them to the frame with the axle screws. Make sure the axle has been screwed on tightly spacer and mount them to the frame with the axle screws. Make sure the axle has been screwed on tightly
before starting again!
HOW TO RIDE AND BRAKE
Place one foot on the baseboard, push forward with the other foot. Steer. Place one foot on the baseboard, push f
ng button will locate into the first recessed hole, to re-adjust de-press the ng button will locate into the first recessed hole, to re
and handlebars spring button are locked properly in place before riding. Keep and handlebars spring button are locked properly in place before riding. Keep
, check the clamp bolt is tightened securely. This
BEARINGS
responsibility of the owner or guardian to periodically inspect the wheels for
ps play, this is an indication of excess wear and replacement is
wheels. Worn tires/ wheels/ wheel bearings are considered normal
fixed with screws, locking nuts, which don't loosen in normal use. However,
bearings require no special maintenance (other than lubrication see: bearings require no special maintenance (other than lubrication see
bearings are worn out or not operating smoothly, please change
els are changed. Put the bearings into the new wheel with the bolt
height positions, undo the quick release lever and pull
nfolding the scooter. Make sure others are
side play and loose parts. When a wheel or
ss wear and replacement is necessary. Replace
nuts before each use. If once loose, following a violent
ating smoothly, please change them.
Ensure the quick release lever
wear to the wheels, hubs and
tube
and fall.
nspect the wheels for wear and
are considered normal
t loosen in normal use. However,
ead locking is necessary to ensure a
ENGLISH