Avdel Genesis nG2 Betriebsanleitung Seite 46

A c c e s s o r i e s
Preparing the Base Tool for Right-Angle and Straight Swivel Head A t t a c h m e n t
•
Disconnect the air supply.
•
Remove any nose assembly items.
•
Remove Stem Collector Bottle Assembly
25 (71213-03800).
•
Replace assembly 25 with Safety Cap
(71213-20201)
•
Unscrew Male 'T' Adaptor 41 and remove
with 'O' Ring 12, Locknut 40, 'O' Rings 19
and 15, and Seal Housing 52. Do not refit
these items.
•
Screw Stop Nut (71213-20200) onto the
front of Head Piston 36 as far as it will go
by hand.
•
Fit Jaw Spreader Housing (71210-02101)
and 'O' Ring 12, tighten onto Head Piston
36, finally tighten Stop Nut against Jaw
Spreader Housing.
The tool is now ready to be fitted with a swivel
head. Instructions page 15.
Item numbers in bold refer to the general
assembly drawing and parts list on pages 24-
25.
R I G H T- A N G L E S W I V E L H E A D c a p a b i l i t y
FASTENER
1
NAME Ø MATERIAL
1 / 8 3.2
AVEX Aluminium Alloy
®
1 / 8 3.2 Steel
5 / 32 4.0 Aluminium Alloy
5 / 32 4.0 Steel
4.8
3 / 16 Aluminium Alloy
BULBEX 5 / 32 4.0 Aluminium Alloy
®
3 / 16 4.8 Aluminium Alloy
1 / 8 3.2 Stainless Steel
II
AVINOX
®
5 / 32 4.0 Stainless Steel
– 4 Aluminium Alloy
®
AVSEAL II
– 4 Aluminium Alloy
– 5
Aluminium Alloy
–
5 Aluminium Alloy
1 / 8 3.2 Steel
STAVEX
®
5 / 32 4.0 Steel
3.2
1 / 8 Stainless Steel
5 / 32 4.0 Stainless Steel
1
In inches then in millimetres.
14
Base tool to receive a nose assembly
41 12 40
19
15
Base tool to receive a swivel head
71213-20200
STOP NUT
SWIVEL HEAD
PART Nº
0 7 3 4 6 - 0 3 0 0 0
0 7 3 4 6 - 0 3 1 0 0
0 7 3 4 6 - 0 3 1 0 0
0 7 3 4 6 - 0 3 2 0 0
0 7 3 4 6 - 0 3 2 0 0
0 7 3 4 6 - 0 3 1 0 0
0 7 3 4 6 - 0 3 2 0 0
0 7 3 4 6 - 0 3 1 0 0
0 7 3 4 6 - 0 3 2 0 0
7 1 2 1 3 - 0 4 0 0 0
7 1 2 1 3 - 0 4 7 0 0
7 1 2 1 3 - 0 4 1 0 0
7 1 2 1 3 - 0 4 8 0 0
0 7 3 4 6 - 0 3 1 0 0
0 7 3 4 6 - 0 3 2 0 0
0 7 3 4 6 - 0 3 1 0 0
0 7 3 4 6 - 0 3 2 0 0
2
Long nose tip for deep placing.
Remove Male 'T' 41 Adaptor from the Tool and replace with Jaw Spreader Housing
(71210-02101). See 'Preparing the Base Tool' above.
52
36
NOSE TIP (mm)
PART Nº 'A'
0 7 3 4 5 - 0 3 6 0 0
7 . 8 7 3 . 8 1
0 7 3 4 5 - 0 3 7 0 0
7 . 8 7 3 . 8 1
0 7 3 4 5 - 0 3 7 0 0
7 . 8 7 3 . 8 1
0 7 3 4 5 - 0 3 8 0 0
7 . 8 7 3 . 8 1
0 7 3 4 5 - 0 3 8 0 0 7 . 8 7 3 . 8 1
0 7 3 4 5 - 0 3 7 0 0
7 . 8 7 3 . 8 1
0 7 3 4 5 - 0 3 8 0 0
7 . 8 7 3 . 8 1
0 7 3 4 5 - 0 3 7 0 0
7 . 8 7 3 . 8 1
0 7 3 4 5 - 0 3 8 0 0
7 . 8 7 3 . 8 1
7 1 2 1 3 - 1 6 4 0 1
6 . 3 5 1 . 9 5
2
7 1 2 1 3 - 1 6 4 0 2 6 . 3 5 4 . 1 1
7 1 2 1 3 - 1 6 4 0 3 7 . 6 2 2 . 0 0
2
7 1 2 1 3 - 1 6 4 0 4 7 . 6 2 4 . 1 1
7 . 8 7 3 . 8 1
0 7 3 4 5 - 0 3 7 0 0
7 . 8 7 3 . 8 1
0 7 3 4 5 - 0 3 8 0 0
7 . 8 7 3 . 8 1
0 7 3 4 5 - 0 3 7 0 0
7 . 8 7 3 . 8 1
0 7 3 4 5 - 0 3 8 0 0
COMPLETE TOOL PART NUMBER :
A
(the stop nut and safety cap are included)
IMPORTANT: in contrast to complete tools
B
with nose assemblies, those fitted with swivel
heads include the nose tip as a part of the head.
71213-20201
SAFETY CAP
View with 25 removed
and stop nut
replacing removed
items 19, 15, 52, 40
JAWS
below
'B' PART Nº
0 7 3 4 0 - 0 0 2 1 3 ... 0 0 1
0 7 3 4 0 - 0 0 2 1 3 ... 0 0 4
0 7 3 4 0 - 0 0 2 1 3 ... 0 0 4
0 7 4 9 0 - 0 4 6 0 2 ... 0 1 0
0 7 4 9 0 - 0 4 6 0 2 ... 0 1 0
0 7 3 4 0 - 0 0 2 1 3 ... 0 0 4
0 7 4 9 0 - 0 4 6 0 2 ... 0 1 0
0 7 3 4 0 - 0 0 2 1 3 ... 0 0 4
... 0 1 0
0 7 4 9 0 - 0 4 6 0 2
0 7 3 4 0 - 0 0 2 1 3 ... 1 6 0
0 7 3 4 0 - 0 0 2 1 3 ... 1 8 0
0 7 3 4 0 - 0 0 2 1 3 ... 1 6 1
0 7 3 4 0 - 0 0 2 1 3 ... 1 8 1
0 7 3 4 0 - 0 0 2 1 3 ... 0 0 4
0 7 4 9 0 - 0 4 6 0 2 ... 0 1 0
0 7 3 4 0 - 0 0 2 1 3 ... 0 0 4
0 7 4 9 0 - 0 4 6 0 2 ... 0 1 0
precede with 71213-40
see