Avdel Genesis nG2 Betriebsanleitung Seite 45

A c c e s s o r i e s
S w i v e l H e a d s
Instead of a nose assembly, a swivel head can be fitted to a base tool. It allows 360° rotation of the tool about the nose tip and allows
access into many applications otherwise too restrictive. There are two types of swivel heads: the straight swivel head with the nose tip
slightly offset from the centre line of the tool head and the right-angle swivel head with the nose tip on a perpendicular axis to the head of
the tool. See drawings below for dimensions and pages 14-15 for detail.
PRIOR to fitting a swivel head, the base tool must be adapted. See Preparing the Base Tool opposite.
In contrast to nose assemblies part numbers of swivel heads do INCLUDE a nose tip as shown below.
Swivel heads are supplied separately for fitting to a base tool forming a complete tool. See table below for part numbers. Jaws and nose
tips vary depending on the fastener to be placed but all other components remain the same within each type of swivel head. See the
'capability' tables below and page 14. For the 'Constant Components' table see page 16.
'A' and 'B' dimensions will help you assess the accessibility of your application.
S T R A I G H T S W I V E L H E A D c a p a b i l i t y
F A S T E N E R
1
NAME Ø MATERIAL
1 / 8
AVEX ® 3.2
Al Alloy
1 / 8 Steel
3.2
5 / 32
4.0
Al Alloy
5 / 32 Steel
4.0
3 / 16
4.8 Al Alloy
® 5 / 32 Al Alloy
BULBEX 4.0
3 / 16
4.8 Al Alloy
® 1 / 8 Stainless Steel
AVINOX II 3.2
5 / 32
4.0 Stainless Steel
–
® 4 Al Alloy
AVSEAL II
– Al Alloy
4
–
5 Al Alloy
– Al Alloy
5
STAVEX ® 1 / 8 3.2 Steel
5 / 32 Steel
3.2
1 / 8 3.2 Stainless Steel
5 / 32 Stainless Steel
4.0
1
In inches then in millimetres.
I M P O R T A N T
S W I V E L H E A D
PART Nº
07345-0 30 00
07345 -0 31 00
07345 -0 31 00
07345 -0 32 00
07345 -0 32 00
07345 -0 31 00
07345 -0 32 00
07345 -0 31 00
07345 -0 32 00
71213 -0 60 00
71213 -0 66 00
71213 -0 61 00
71213 -0 67 00
07345 -0 31 00
07345 -0 32 00
07345 -0 31 00
07345 -0 32 00
2
Long nose tip for deep placing.
Remove Male 'T' Adaptor 41 from the Tool (see page 16) and replace with
Jaw Spreader Housing (71210-02101).
N O S E T I P ( m m )
PART Nº 'A' 'B'
0 734 5-036 00 7 .87 3.81
0 734 5-037 00 7 .87 3.81
0 734 5-037 00 7 .87 3.81
0 734 5-038 00 7 .87 3.81
0 734 5-038 00 7 .87 3.81
0 734 5-037 00 7 .87 3.81
0 734 5-038 00 7 .87 3.81
0 734 5-037 00 7 .87 3.81
0 734 5-038 00 7 .87 3.81
7 121 3-164 01
6 .35 1.95
2
6 .35 4.11
7 12 13-16 402
7 .62 2.00
712 13 -16 40 3
2 7 .62 4.11
71 213 -1 640 4
7 .87 3.81
073 45 -03 70 0
7 .87 3.81
073 45 -03 80 0
7 .87 3.81
073 45 -03 70 0
073 45 -03 80 0 7 .87 3.81
COMPLETE TOOL PART NUMBER :
A
(the stop nut and safety cap are included)
IMPORTANT: in contrast to complete tools
B
with nose assemblies, those fitted with swivel heads
include the nose tip as a part of the head.
see
J A W S
b elow
PART Nº
07 34 0-0 02 13 ... 0 0 1
07 34 0-0 02 13 ... 0 0 4
... 0 0 4
07 34 0-0 02 13
07 49 0-0 46 02 ... 0 1 0
... 0 1 0
07 49 0-0 46 02
07 34 0-0 02 13 ... 0 0 4
07 49 0-0 46 02 ... 0 1 0
07 34 0-0 02 13 ... 0 0 4
07 49 0-0 46 02 ... 0 1 0
07 34 0-0 02 13 ... 1 6 0
07 34 0-0 02 13 ... 1 8 0
07 34 0-0 02 13 ... 1 6 1
07 34 0-0 02 13 ... 1 8 1
07 34 0-0 02 13 ... 0 0 4
07 49 0-0 46 02 ... 0 1 0
07 34 0-0 02 13 ... 0 0 4
07 49 0-0 46 02 ... 0 1 0
precede with 71213-30
13