Maintenance Instruction - Herth+Buss ELPARTS Reanimator Bedienungsanleitung

Operating Instruction
1. Complete charging may take up to 24
hours.
EN
NOTE: The yellow CHARGING LED on
the charge will remain flashing after
display shows 100%, because charger
enters automatically into maintaining
mode.
2. After charge is complete and the boos-
ter is ready for use, disconnect the
charger from the AC outlet, and then
disconnect the charger from booster.
7. Operating instructions
7.1. Jump starting a vehicle engine
WARNING
A spark near the battery may
cause a battery explosion. To
reduce the risk of a spark
near the battery.
1. Turn the vehicle's ignition OFF before
making cable connections.
2. Connect the booster to the vehicle's
battery as described in section 4.
If you have connected the clamps
backward, an audio alarm will sound.
DO NOT turn the booster ON/OFF switch
to the ON position. This could cause
serious damage to the booster or the
vehicle. Reverse the connections and the
audio alarm will stop.
3. Turn the booster ON/OFF switch to the
ON position.
4. Crank the engine. If the engine does not
start within 8 seconds, stop cranking and
www.herthundbuss.com
95980806 | 95980807
wait at least 3 minutes before attempting
to start the vehicle again. This permits
the booster battery to cool down.
5. After the engine starts, immediately turn the
booster ON/OFF switch to the OFF position.
6. Disconnect the booster from the vehicle,
as described in section 4.6.
7. Return the battery clamps to the clamp
holders. Recharge the booster as soon as
possible after use.
7.2. When using the other features of the
booster, always observe the following steps:
1. Ensure the battery clamps are securely
clipped on the clamp holders.
2. Charge the booster as soon as possible
after using the feature.
7.3. Powering a 12V DC device:
The booster is a power source for all 12V
DC accessories that are equipped with a 12V
accessory plug. Make sure the device to be
powered is OFF before inserting the 12V DC
accessory plug into the 12V DC accessory
outlet.
1. Open the protective cover of the DC po-
wer outlet on the front of the booster.
2. Plug the device into the outlet and turn
the device on (if required).
3. If the device draws more than 15A or has
a short circuit, the circuit breaker of the
booster will trip and disconnect the po-
wer to the device. Disconnect the device
and the beaker will automatically reset.
The DC power outlet is wired directly to
the internal battery. Extended operation
of a 12V device may result in excessive
battery drain. Recharge immediately
Operating Instruction
after unplugging the device.
7.4 Powering a USB Device
The booster is a power source for all accesso-
ries that are equipped with a USB plug. The
USB port provides up to 2.1A at 5V DC.
1. Ensure the battery clamps are securely
clipped on the storage holders.
2. Press the USB button on the front of
the unit.
3. Plug the device into the USB port on the
front of the unit.
4. Turn the USB device on.
5. Reverse these steps when finished using
the USB port.
NOTE
The USB port will shut-off automati-
cally after 60 minutes, if no device is
connected. Extended operation of a
USB device may result in excessive
battery drain. Recharge the booster im-
mediately after unplugging the device.
8. Fuse replacement for the booster
The booster is equipped with an inline fuse,
to protect the battery from overload.
Fuse Specification:
Booster 12V:
Fast blow, DC automotive type, rated 32V,
300A (Bussman/Audio Ohm Srl)
Booster 12/24V:
Fast blow, DC automotive type, rated 32V,
500A (Bussman/Audio Ohm Srl)
24 25
95980806 | 95980807
WARNING
Keep away from sparks and flame –
battery could emit explosive gases.
1. Allow the fuse to cool
down completely (approxi-
mately 5 minutes).
2. Make sure the switch
is in the OFF position
and the unit is unplugged from the
external charger.
3. Remove the positive (RED) clamp from the
side of the unit and locate the fuse holder.
4. Open the fuse holder by removing
its cover.
5. Using a wrench, remove the first nut and
bolt securing the fuse on the positive
cable. Repeat the same steps for the
second nut and bolt. Remove the open
fuse and replace it with a new one of the
same type and rating.
6. Tighten the nuts and bolts to secure the
fuse, and then replace the cover of the
fuse holder.
7. The unit is now ready to use.

9. Maintenance instruction

9.1. Cleaning and user maintenance should
not be done by children without supervision.
9.2. Unplug the charger from the booster
before attempting any maintenance or
cleaning.
9.3. Use a dry cloth to wipe all battery cor-
rosion and other dirt or oil from the battery
clamps, cords and the booster case. Do not
use cleaning fluids.
EN