Practical Tips - EINHELL TC-MG 250 CE Originalbetriebsanleitung

•
Secure the plug-in tool using the supplied
screw (5) and tighten the screw securely with
the Hexagon key (7).
•
Make sure that the washer (4) is used for the
screw (5) (see Figure 2). The camber on the
washer must face upwards.
Warning!
Check that the plug-in tool is secure.
5.2 Triangular sanding/grinding plate
Fit the triangular sanding/grinding plate to use the
equipment as a delta sander/grinder.
5.2.1 Fastening the sanding/grinding paper
The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the va-
cuum extraction holes on the sanding/grinding
paper and the sanding/grinding disk are aligned.
5.3 Fitting the dust extraction device for the
grinding/sanding plate (Fig. 3/4)
The dust extraction system prevents the accumu-
lation of dirt and high dust loads in the air, and it
makes it easier to dispose of the dust.
•
Place the equipment in a stable position as
shown in 5.1.
•
Fit the dust extraction device (6) with the tool
mounting (2) positioned as shown in Figure 3.
•
Turn the dust extraction device (6) as shown
in Fig. 4 until it latches in place.
•
Make sure that the washer (4) is used for the
screw (5) (see Figure 2). The camber on the
washer must face upwards.
•
Place the triangular grinding/sanding plate
on the dust extraction device (6) and the
tool mounting (2) so that the pins of the tool
mounting (2) fit into the recesses of the trian-
gular grinding/sanding plate (8), then fasten
as shown in Fig. 6.
•
Connect your tool to an extraction unit or va-
cuum cleaner. This will provide excellent ext-
raction of chips and dust from the workpiece.
The benefi ts are that you will protect both the
equipment and your own health. Your work area
will also be clean and safe.
Anl_TC_MG_250_CE_SPK13.indb 15 Anl_TC_MG_250_CE_SPK13.indb 15
GB
6. Operation
6.1 Switching on/off (Fig. 7)
Slide the switch (1) forwards to switch on the
equipment.
Slide the switch (1) to the rear to switch off the
equipment.

6.2 Practical tips

•
Switch on the equipment.
•
Work away from the body.
•
Never move your hands into the direct vicinity
of the work area.
•
Use only plug-in tools which are in good wor-
king order and undamaged.
Plug-in tools
Sawing: Sawing wood and plastic.
Notes on working practice:
When sawing, watch out for foreign bodies in the
workpiece and remove these if necessary. Plunge
cutting is allowed only in soft materials such as
wood or plasterboard.
Sanding/grinding: Surface sanding/grinding at
edges, in corners or hard-to-reach areas. Depen-
ding on choice of sanding/grinding paper for the
sanding/grinding of wood, paint, lacquer, etc.
Notes on working practice:
This equipment off ers particularly high perfor-
mance for the sanding/grinding of hard-to-reach
corners and edges. To sand/grind profi les and
channels you can also work with just the tip or
the edge of the sanding/grinding disk. Various
sanding/grinding papers are available, specially
designed for the diff erent types of material you
may be working on and the amount you wish to
remove from the surface. The amount removed
will depend largely on the choice of sanding/grin-
ding paper and pressure applied to the sanding/
grinding disk.
Scraping: Scraping off old paint or adhesives.
Notes on working practice:
Move the plug-in tool against the area you want to
remove. Begin with a fl at angle of incidence and
little pressure. The surface (e.g. wood, plaster)
may be damaged if too much pressure is used.
- 15 -
25.08.2022 13:36:41 25.08.2022 13:36:41