Switching On/Off; Practical Tips - EINHELL TE-MG 350 EQ Originalbetriebsanleitung

•
Place the plug-in tool (e.g. the scraper) on
the tool chuck (2) so that the pins of the tool
chuck fit into the recesses in the plug-in tool.
The tool chuck (2) is magnetic in order to
secure the plug-in tool during the clamping
procedure.
•
Close the quick-release lock for changing
tools (5) again. Take care that the pins of the
chuck (2) remain in the recesses in the plug-
in tool.
•
The equipment comes with a disk (6) for
safely securing plug-in tools with recesses.
Please note the correct use (camber facing
the tool) of the disk (6) for plug-in tools with
recess as shown in Fig. 7 and 8.
Check that the plug-in tool is secure.
5.2 Triangular sanding/grinding plate
Fit the triangular sanding/grinding plate to use the
equipment as a delta sander/grinder.
5.2.1 Fastening the sanding/grinding paper
Easy replacement using hook-and-loop fastening.
Make sure that the vacuum extraction holes on
the sanding/grinding paper and the sanding/grin-
ding disk are aligned.
5.3 Fitting the dust extraction device
(Fig. 4/5)
The dust extraction device prevents the accumu-
lation of dirt and high dust loads in the air, and it
makes it easier to dispose of the dust.
•
Open the quick-release lock for changing
tools and place the equipment in a stable po-
sition as described in 5.1.
•
Mount the dust extraction adapter (3) on the
tool chuck (2) as shown in Fig. 4.
•
Turn the dust extraction adapter (3) as shown
in Fig. 5 until it latches in place.
•
Connect your tool to an extraction unit or va-
cuum cleaner. This will provide excellent ext-
raction of chips and dust from the workpiece.
The benefi ts are that you will protect both the
equipment and your own health. Your work area
will also be clean and safe.
Anl_TE_MG_350_EQ_SPK13.indb 16 Anl_TE_MG_350_EQ_SPK13.indb 16
GB
6. Operation
6.1 Switching on/off
Slide the switch (1) forwards to switch on the
equipment.
Slide the switch (1) to the rear to switch off the
equipment.

6.2 Practical tips

•
Switch on the equipment.
•
Work away from the body.
•
Never move your hands into the direct vicinity
of the work area.
•
Use only plug-in tools which are in good wor-
king order and undamaged.
Plug-in tools
Sawing
Sawing wood and plastic.
Notes on working practice
When sawing, watch out for foreign bodies in the
workpiece and remove these if necessary. Plunge
cutting is allowed only in soft materials such as
wood or plasterboard.
Sanding/grinding
Surface sanding/grinding at edges, in corners
or hard-to-reach areas. Depending on choice of
sanding/grinding paper for the sanding/grinding
of wood, paint, lacquer, etc.
Notes on working practice
This equipment off ers particularly high perfor-
mance for the sanding/grinding of hard-to-reach
corners and edges. To sand/grind profi les and
channels you can also work with just the tip or
the edge of the sanding/grinding disk. Various
sanding/grinding papers are available, specially
designed for the diff erent types of material you
may be working on and the amount you wish to
remove from the surface. The amount removed
will depend largely on the choice of sanding/grin-
ding paper and pressure applied to the sanding/
grinding disk.
Scraping
Scraping off old paint or adhesives.
Notes on working practice
Move the plug-in tool against the area you want to
remove. Begin with a fl at angle of incidence and
little pressure. The surface (e.g. wood, plaster)
may be damaged if too much pressure is used.
- 16 -
25.08.2022 13:04:40 25.08.2022 13:04:40