Eufab 16404 Bedienungsanleitung Seite 4

Bicycle wall mount
OVERVIEW
1. INTENDED USE ______________________________4
2. SCOPE OF DELIVERY ___________________________4
3. SPECIFICATIONS _____________________________4
4. SAFETY NOTES ______________________________4
5. OPERATING INSTRUCTIONS ______________________4
6. CARE AND MAINTENANCE _______________________5
7. NOTES FOR ENVIRONMENTAL PROTECTION _____________5
8. CONTACT INFORMATION ________________________5
WARNING
Read the operating instructions through careful-
ly prior to initial use and observe all of the safety
notes! Store original packaging, proof of purchase
as well as these instructions for future reference!
Not observing such may lead to personal injury,
damages to the device or your property! Prior to
initial use, check the contents of the packaging
to ensure that they are in perfect condition and
complete!
1. INTENDED USE
The wall mount is designed for storing bicycles, surfboards or ladders
to the wall. The load on the wall mount may not exceed 45 kg. The
supplied fixtures are designed only for masonry or cement walls.
Any use other than those described above is not permitted.
This device is not designed to be used by children or persons with
limited mental abilities or without experience and/or lack of required
specialist knowledge. Keep children away from the device.
The device is not designated for commercial use.
Use according to the intended purpose also includes the observance
of all information in these operating instructions, particularly the ob-
servance of the safety notes. Any other utilisation is considered to be
contrary to the intended purpose and may lead to material damage or
personal injuries. EAL GmbH assumes no liability for damage resulting
from improper use.
2. SCOPE OF DELIVERY
A 2 Bar with end cap
B 2 Carrier arm with humped profile and end caps
C 2 Toothed joint, 2 pieces
D 2 Knob nut
E 2 Washer
F 2 Lock screw
4 Cross-headed screw 4 x 65
4 Dowels 8 mm
A
C
F
B
4
A
D
E
3. SPECIFICATIONS
Dimensions (L x W x H): approx. 57 x 54 x 49 [cm]
Net weight: approx. 1,950 kg
Length of carrier arms: approx. 52 cm
Maximum load: 45 kg
4. SAFETY NOTES
• The warning sign indicates all instructions which are
important for safety. Always observe these, otherwise you
can injure yourself or the article could be damaged.
• Children should not play with the article.
• Do not treat packaging material carelessly. This may
become a dangerous plaything for a child!
• Keep children away and do not permit children to use this
device!
• Only use this product for the intended use!
• Do not manipulate or disassemble the device!
• For your own safety, only use accessories or replacement
parts specified in the instructions or that the manufacturer
has recommended!
• The fixtures are to be adapted to the properties of the
relevant wall, if necessary obtain specialist advice!
• The selection of an unsuitable installation location may
result in injury or property damage.
• Carry out the installation very conscientiously since if the
bicycle falls, it will not only result in expense consequential
damages, but also an increased risk of injuries.
• Always, set the angle of the carrier arms in such a way that
the object being stored cannot slide out,
• Make sure that the toothed joints and the screw fastenings
are tightened before you place a load on the carrier arms.
• Check all screw connections regularly. The screw
connections may loosen over time with the loading and
unloading of the wall mount.
5. OPERATING INSTRUCTIONS
Joint the two bar elements (A). Mark the position of the holes for the bar on
a suitable wall. Make sure that the wall mount can be mounted precisely
horizontally so that the objects being stored cannot slip at a later time.
Secure the bar to the wall using the dowels and the cross-headed screws.
Push the lock screws (F) through the drilled holes in the carrier arms (B).
Place the two halves of the toothed joints (C) on the screws. Adjust the
angle of the toothed joints to their application, press the joint together
and insert the screws through the lower hole of the bar.
Now, first place the washers (E) on the screws and then on the knob
nuts (D). If you are sure that the brackets for the carrier arms are correct,
tighten the knob nuts firmly.
Check the firm hold of the wall mount before placing the first load on it.
When the wall mount is not required, the carrier arms can be folded back
to save space. Undo the knob nuts so that you are able to pull the teeth
of the joint apart. Fold the carrier arm down or up to the wall and then
tighten the lock nuts up again.