Lionelo Nebi Air Mask Bedienungsanleitung Seite 5

A. Container components
1.
Cover
2.
Medicine cup
3.
Spray nozzle
Assembly
• Attach the container to the main device unit. The container is attached correctly when you hear a characteristic click (Fig. 2). Next, install the appropriate mask
or mouthpiece (Fig. 3).
PLEASE NOTE! Before use, clean, disinfect and dry all the device parts as instructed in the "Cleaning and disinfection" chapter.
Power supply
•
To charge the nebulizer, use the USB cable and an appropriate adapter with the output parameters of 5.0 V DC 1.0 A.
•
The device power supply system has one lithium battery.
•
To charge a discharged battery, connect the device to the mains (Fig. 4).
Please note! Before you charge, ensure that the mains socket has the suitable voltage.
Please note! The device has an autonomous charging system. Do not charge together with any other electronic equipment.
Battery charging
• The fully-charged battery may supply power to the device for up to 60 minutes continuously.
• Low battery level is indicated by a LED which is going to blink blue 5 times and then switch off.
• Use the charger to charge the battery. Ca. 2 hours are required to charge it completely.
•
The LED blinks when charging and is solid when it is fully charged.
Operation manual (Fig. 5)
1.
LED
LED is solid blue
LED blinks blue 3 times
2.
Preparation: Before use, clean, disinfect and dry all the device components as instructed in the "Cleaning and disinfection" chapter.
3.
Pouring liquid: open the cover, inject the solution and close the cover. Please note! Before you switch the device on, pour the liquid into the cup.
Please note: protection from leakage! When you pour the medicine into the medicine cup, ensure that you fill it up to the maximum value (6 ml). The recommended
liquid amount is 2 to 6 ml. Nebulization takes place solely when the substance to be produced has contact with the mesh disc. Otherwise, nebulization stops
automatically. Keep the device upright.
4. Nebulization
• Before you start nebulizing, shake the device horizontally to stir the solution. Based on your individual needs, use the following two nebulization methods (see Fig. 6).
• Put on the mask or place the mouthpiece between your lips and press the power button.
A – Nebulizing with a mouthpiece
•
Take a slow, deep breath and wait until the medication release starts.
•
The nebulizer switches off automatically in 10 minutes. To extend the use, press the power button. Ensure there is sufficient liquid in the medicine cup.
•
After nebulization is completed, press the power button to switch the device off. Press the container unlocking button, remove the container and empty it (Fig. 7).
•
To install the container, press the "press" button and slide the container in the device vertically. Ensure that the container is located correctly (Fig. 8).
•
Please note! The liquid may start thickening round the nozzle and the mesh disc which may affect the nebulization result. Stop nebulizing, remove the mouthpiece
The mean particle size in the nebulizer is measured in a 0.9% saline solution at 25°C and relative
humidity of 59% R.H. The equivalent distribution curve for mist particle size in the said condition is
as follows:
Please note! The horizontal axis is the particle size value. The value is a log distribution. The left
vertical axis is a cumulative size percentage corresponding to the increasing curve trend. The right
vertical axis is a percentage value of the section corresponding to the histogram.
Kit
The kit includes the main unit, medicine cup, USB power cord, adult mask, child mask and mouthpiece.
Part list (Fig. 1)
4.
Main unit
5.
Power switch
6.
USB port
7.
Electrode contacts
Operating
No liquid / The device is not vertical
/ Switching off
B – Nebulizing with a mask
8.
Child mask
9.
Adult mask
10. Headband
11. Cup unlocking button
LED blinks blue 5 times
LED blinks green
LED is solid green
12. Mouthpiece
13. Mesh disc
Low battery / Switching off
Charging
Battery fully charged