ABB i-bus® KNX PARAMETER
Treppenlichtzeit
•
Überwachungsart [Gruppe]
•
•
Überwachungsart [Kanal]
•
unterer Schwellwert
Verhalten bei Ergebnis "0" [Schaltaktor]
•
Verhalten bei Ergebnis "1" [Schaltaktor]
•
•
Verhalten bei Szenenaufruf
•
Verhalten des Ausgangs
•
Verhalten nach Blinken
Verhalten nach Busspannungswiederkehr [Schaltaktor]
•
Verhalten nach ETS-Download [Schaltaktor]
•
•
Verzögerung
•
Warnung vor Ausschalten des Treppenlichts
Warnzeit
•
Wert Kommunikationsobjekt "Kontakt geschlossen und kein Strom fließt" senden
•
•
Wert Kommunikationsobjekt "Kontakt offen und Strom fließt" senden
•
Wert Kommunikationsobjekt "Status Ergebnis" senden
•
Wert Kommunikationsobjekt "Status Hauptzähler Energieverbrauch" senden
Wert Kommunikationsobjekt "Status Lastabschaltung" senden
•
Wert Kommunikationsobjekt "Status Leistung" senden
•
•
Wert Kommunikationsobjekt "Status Schalten" senden
•
Wert Kommunikationsobjekt "Status Schalten"
Wert Kommunikationsobjekt "Status Strom" senden
•
Wert Kommunikationsobjekt "Verknüpfung A" nach Busspannungswiederkehr
•
•
Wert Kommunikationsobjekt "Verknüpfung B" nach Busspannungswiederkehr
•
Wert Kommunikationsobjekt, wenn Kontakt geschlossen und kein Strom fließt
•
Wert Kommunikationsobjekt, wenn Kontakt offen und Strom fließt
Wert Kommunikationsobjekt, wenn Last ein/aus [Gruppe]
•
Wert Kommunikationsobjekt, wenn Last ein/aus [Kanal]
•
•
Wert Kommunikationsobjekt, wenn Last in Betrieb [Gruppe]
•
Wert Kommunikationsobjekt, wenn Last in Betrieb [Kanal]
Wert Kommunikationsobjekt, wenn Last in Standby [Gruppe]
•
Wert Kommunikationsobjekt, wenn Last in Standby [Kanal]
•
•
Wert Kommunikationsobjekt, wenn Last in Überlast [Gruppe]
•
Wert Kommunikationsobjekt, wenn Last in Überlast [Kanal]
•
Wert Kommunikationsobjekt, wenn Last in Unterlast [Gruppe]
Wert Kommunikationsobjekt, wenn Last in Unterlast [Kanal]
•
Wert Kommunikationsobjekt, wenn Maximalschwellwert überschritten [Gruppe]
•
•
Wert Kommunikationsobjekt, wenn Maximalschwellwert überschritten [Kanal]
•
Wert Kommunikationsobjekte "Statusbyte" senden [Schaltaktor]
Wert nach Ablauf der Sende- und Schaltverzögerung
•
Wert wird gesendet ab einer Änderung von
•
•
Wertänderung auswerten als
•
Werte Kommunikationsobjekte "Status Ergebnis" und "Status Eingangswert zwischen den Schwell-
werten" senden
Werte Spannung/Leistungsfaktor bei Download überschreiben
•
Werte Spannung/Leistungsfaktor über i-bus Tool ändern
•
•
Werte Spannung/Leistungsfaktor über Kommunikationsobjekte ändern
•
Zeit für Aus
Zeit für Ein
•
Zeitstempel Start Hauptzähler [Gruppe]
•
•
Zeitstempel Start Hauptzähler [Kanal]
•
Zentrales Kommunikationsobjekt "Lastabschaltstufe empfangen" freigeben
•
Zentrales Kommunikationsobjekt "Schalten" freigeben
Zentrales Kommunikationsobjekt "Szene 1 ... 64" freigeben
•
Zugriff i-bus® Tool
•
•
Zuordnung zur Energiegruppe x
•
Zwangsführung (1 Bit / 2 Bit) [Schaltaktor]
Hinweis zur Navigation im PDF: Tastenkombination 'Alt + Pfeil links'
springt zur vorherigen Ansicht/Seite
Seite 164
,
Seite 167
,
,
Seite 168
,
Seite 169
,
Seite 171
,
Seite 172
,
Seite 172
,
Seite 176
Seite 177
,
,
Seite 194
,
Seite 195
,
Seite 197
Seite 197
,
Seite 199
,
,
Seite 200
Seite 170
,
Seite 171
,
Seite 172
,
Seite 174
,
,
Seite 176
,
Seite 178
,
Seite 181
,
,
Seite 183
,
Seite 183
Seite 184
,
Seite 187
,
Seite 188
,
,
Seite 188
,
Seite 189
Seite 189
,
Seite 190
,
,
Seite 190
,
Seite 191
,
Seite 192
,
Seite 194
,
Seite 194
,
Seite 196
,
Seite 197
,
,
Seite 198
,
Seite 199
Seite 199
,
,
Seite 200
Produkthandbuch | DE | SA/S x.16.6.2 | 9AKK107680A8850 Rev. C 109
Seite 177
,
,
Seite 178
,
Seite 179
Seite 181
Seite 185
,
,
Seite 186
,
Seite 186
,
Seite 187
Seite 191
Seite 192
,
,
Seite 193
,
Seite 193
Seite 195
,
,
Seite 196
,
Seite 198