Montageanleitung ABT AEC für 2,0 BTD T6.1 EU6 AP 2 Informationen zur Stromaufnahme Durch die Verwendung einer Leistungssteigerung in Verbindung mit AEC erhöht sich die Stromaufnahme des Fahrzeugs. Es fließt ein zusätzlicher Strom. Der Gesamtstrom ist überdies abhängig von Fahrzeugtyp, Zusatzausstattung und ähnlichem. Im Einzelfall ist ein deutlich höherer Stromverbrauch möglich.
Montageanleitung ABT AEC für 2,0 BTD T6.1 EU6 AP 3 Lieferumfang Bitte kontrollieren Sie die Vollständigkeit des Lieferumfanges vor dem Beginn des Einbaus. Sollte die Lieferung unvollständig sein, setzen Sie sich bitte mit ABT Sportsline GmbH in Verbindung. Menge Bild...
Montageanleitung ABT AEC für 2,0 BTD T6.1 EU6 AP 4 Vorbereitungen am Fahrzeug Hinweis Warten bis das Auto eingeschlafen ist (Busruhe). Positionen der Sensoren A Railsensor / rail pressure (Roter Pfeil) B Ladedruckgeber 2 / manifold pressure (Grüner Pfeil) C Hallgeber / camshaft position...
Montageanleitung ABT AEC für 2,0 BTD T6.1 EU6 AP 5 Verlegung Sensorkabelbaum A Railsensor abstecken und mit dem ABT (rail pressure) Stecker verbinden. Kabelbaum scheuerfrei und Wärme- schonend verlegen. B Ladedruckgeber 2 abstecken und mit dem ABT (manifold pressure) Stecker verbinden.
Seite 10
Montageanleitung ABT AEC für 2,0 BTD T6.1 EU6 AP D Luftmassenmesser (Air mass meter) abstecken und mit dem ABT (Air mass meter) Stecker verbinden. Kabelbaum scheuerfrei und Wärme- schonend verlegen. Masseleitung (GND) an dem Massepunkt der Batterie befestigen. Dauerplus (+12V) an dem Batteriepol mit anschließen.
Montageanleitung ABT AEC für 2,0 BTD T6.1 EU6 AP 7 Fertigstellung Fehlerspeicher auslesen und gegebenenfalls löschen. Fahrzeug starten und Probefahrt durchführen. Aufkleber "ABT Power" auf der Motorabdeckung und Aufkleber "ABT Information" auf dem Schloßträger anbringen. Nur Otto Motoren: Aufkleber "98 ROZ Super Plus" in der Tankklappe anbringen.
Seite 17
Mountinginstruction AEC for 2,0 BTD T6.1 EU6 AP Table of contents ..............1 Notes ..............2 Current Consumption Information ..............3 Scope of supply ..............4 Preparation work on the vehicle ..............5 Positioning the Sensor Wiring Harness ..............6 AEC positioning ..............
Mountinginstruction AEC for 2,0 BTD T6.1 EU6 AP 2 Current Consumption Information The use of a performance upgrade by installing the AEC raises the vehicle power consumption. Additional power flows. In addition, the total power is dependent on the vehicle model, optional extras, or similar.
Mountinginstruction AEC for 2,0 BTD T6.1 EU6 AP 3 Scope of supply Please check the completeness of delivery before starting the installation. In case the delivery is incomplete, please contact ABT Sportsline GmbH. Quantity Photo Description ABT Engine Control Wiring harness "ABT Power"...
Mountinginstruction AEC for 2,0 BTD T6.1 EU6 AP 4 Preparation work on the vehicle Note Ensure that the vehicle is in sleep mode (idle bus). Positions of the sensors A Rail sensor / rail pressure (red arrow) B Boost pressure sensor 2 /...
Mountinginstruction AEC for 2,0 BTD T6.1 EU6 AP 5 Positioning the Sensor Wiring Harness A Disconnect the rail sensor and connect it to the ABT (rail pressure) connector. Position the wiring harness in such a way that it is protected from abrasion and away from heat.
Seite 25
Mountinginstruction AEC for 2,0 BTD T6.1 EU6 AP D Disconnect the air mass meter and connect it to the ABT (air mass meter) connector. Position the wiring harness in such a way that it is protected from abrasion and away from heat.
Information” sticker to the hood lock support. Gasoline engines only: Affix the "98 RON Super Plus" sticker to the fuel filler flap. Note: The AEC can stay fitted when a workshop carries out control unit updates. The AEC does not interfere with communication with the tester.