Troubleshooting - TFA 30.3056 Bedienungsanleitung

TFA_No. 30.3056_Anleitung_05_16
VENICE - Wireless pool thermometer
• Check the transmission of the signal from the pool sensor to the basic station
(transmission range of up to 50 m in free field). In case of solid walls, especially
with metal parts, the pool transmission range can be considerably reduced.
• If necessary choose another position for the basic station.
10. Additional transmitter (Cat.No. 30.3208.02) optionally available
• Beside the pool sensor, the basic station is able to receive 7 additional transmitters
for the control of indoor (e.g. children's room, wine-cellar etc.) or outdoor climate.
10.1 Elements Transmitter (Fig. 6):
Housing front:
F 1: Transmission signal lamp
Display:
F 2: Channel number
F 3: Temperature and humidity
Housing rear:
F 4: Wall mounting hole
F 5: Battery compartment
in the battery compartment:
F 6: Switch 1, 2, 3 and 4
10.2 Install the optional transmitters
1. Open the screwed battery compartment of the transmitter.
2. For the first transmitter (channel number two), slide down the first and the second
switch and slide up the third switch.
3. It is recommended to let the fourth switch permanently in the upper position, as
the basic station receives the temperature only in degrees Celsius (°C).
4. Insert two new batteries 1,5 V AAA, polarity as illustrated. On the display appear
the measured temperature and humidity and the channel number 2.
5. Channel number one is automatically reserved for the pool sensor.
6. Close the battery compartment again.
• If you want to connect further transmitters, repeat the steps for channel number
three until eight. The correct switch position for the transmitter 2-8 can be found
in the table.
Switch (F 6)
1 2
down down
down up
down up
up down
up down
up up
up up
— —
24
23.05.2016 11:09 Uhr Seite 13
Function
3 4
up up CHANNEL 2
down up CHANNEL 3
up up CHANNEL 4
down up CHANNEL 5
up up CHANNEL 6
down up CHANNEL 7
up up CHANNEL 8
— up °C
VENICE - Wireless pool thermometer
10.3 Reception of the transmitters by the basic station
• The basic station tries to receive the outdoor temperature and humidity values of
the transmitters on channel number two until eight.
• You can also start the search for the transmitter manually. Choose the correspon-
ding channel with the CHANNEL/+ button and press und hold the CHANNEL/+
button for three seconds. A short beep will be heard and the basic station will
scan the outdoor values.
• Press the CHANNEL/+ button on the basic station to display sequentially the out-
door values for the desired transmitters. On the display appear the indoor values
or the selected transmitter.
• Press the CHANNEL/+ button again after the last installed transmitter, on the dis-
play appears the circle symbol. On the upper display the values of the indoor sen-
sor and the installed transmitters are displayed in sequence. To deactivate the
function press the CHANNEL/+ button again.
• With the MIN/MAX/- button you can recall the highest and lowest temperature
and humidity values for all installed transmitters.
10.4 Positioning and fixing of the transmitters
• With the hanging hole at the back of the transmitter, the transmitter can be wall
mounted at the respective location. Placed outside, choose a shady and dry posi-
tion for the transmitter. (Direct sunshine falsifies the measurement and continu-
ous humidity strains the electronic components needlessly).
11. Care and maintenance
• Clean the devices with a soft damp cloth. Do not use solvents or scouring agents.
• For a very good function keep the solar panel always clean. Clean the solar panel
with a soft cloth and maybe a little glass- or display cleaner.
• After every battery replacement in the pool sensor, use a small amount of silicone
grease for the seals.
• Remove the batteries if you do not use the devices for a long period of time.
• Keep the devices in a dry place.
11.1 Battery replacement
• Change the batteries of the basic station, when the battery symbol appears in the
upper display beside the indoor temperature.
• Change the batteries of the pool sensor, when the battery symbol appears in the
lower display beside the pool temperature.
• Change the batteries of the corresponding transmitter, when the battery symbol
appears in the upper display beside the channel no. 2-8.
• Please note: When the batteries are changed, the contact between sensor and
basic station must be restored – so always insert new batteries into all units or
start a manual transmitter search.

12. Troubleshooting

Problems Solution
No indication on the basic ➜ Ensure that the batteries' polarities are correct
➜ Change the batteries
station/pool sensor
25