Router Safety Warnings - Maktec MT362 Betriebsanleitung

ENGLISH
(Original instructions)
1 Nylon nut
2 Stopper pole
3 Fast-feed button
4 Adjusting hex bolt
5 Stopper
6 Lock lever
7 Knob
8 Chip deflector
9 Hex nut
10 Switch lever
11 Shaft lock
12 Wrench
13 Workpiece
14 Bit revolving direction
15 View from the top of the tool
16 Feed direction
SPECIFICATIONS
Model
Collet chuck capacity
Plunge capacity
No load speed (min
Overall height
Net weight
Safety class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.35 Ohms it can be presumed that
there will be no negative effects.
The mains socket used for this device must be protected
with a fuse or protective circuit breaker having slow trip-
ping characteristics.
6
All manuals and user guides at all-guides.com
Explanation of general view
17 Straight guide
18 Thumb screw (A)
19 Guide holder
20 Fine adjusting screw
21 Thumb screw (B)
22 Thumb screw
23 More than 15 mm
24 Wood
25 Templet guide
26 Screws
27 Base plate
28 Bit
29 Base
30 Templet
31 Distance (X)
–1
)
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or serious
injury.
ENE010-1
Save all warnings and instructions for future refer-
ence.

ROUTER SAFETY WARNINGS

ENF002-2
1.
2.
ENF100-1
3.
4.
5.
6.
7.
8.
9.
32 Outside diameter of the templet
guide
33 Thumb screw (C)
34 Trimmer guide
35 Guide roller
36 Thumb screws (B)
37 Screw
38 Dust cover
39 Collet nut
40 Collet cone
41 Spacer
42 Vaccum head
43 Support
44 Limit mark
45 Brush holder cap
46 Screwdriver
MT362
12 mm or 1/2"
0 – 60 mm
22,000
300 mm
5.5 kg
/II
Hold power tool by insulated gripping surfaces,
because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts
of the power tool "live" and shock the operator.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control.
Wear hearing protection during extended period
of operation.
Handle the bits very carefully.
Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly with both hands.
Keep hands away from rotating parts.
Make sure the bit is not contacting the work-
piece before the switch is turned on.
GEA010-1
GEB018-4