Makita VR001G Betriebsanleitung Seite 11

Mode selector
The speed (frequency) of vibrations can be changed in
t w o le v els using the mode selector.
Press the mode b utton to toggle the v i b rations in normal
mode (1) and power mode ( ). Either of the two indica-
tors for the mode y ou select lights up.
Fig.15: 1. Normal mode indicator (1) 2. Po w er
mode indicator ( ) 3. Mode b utton
Mode
Vibrations
(Indication
per minute
number)
- 1
1 2 ,0 0 0 min
Normal
mode (1)
- 1
1 5 ,5 0 0 min
Pow er
mode ( )
NOTE: T he mode y ou select w ill b e sa v ed automat-
ically when the tool is powered o . The tool restarts
in the same mode as it pre v iousl y used w hen turned
on again.
NOTE: When the b atter y protection s y stem w orks,
the mode indicators turn o .
NOTE: When the remaining b atter y capacit y
b ecomes lo w , either of the t w o indicators for the mode
y ou are currentl y using w ill b link. T he timing, at w hich
the lamp starts b linking depends on the temperature
at w ork place and the b atter y cartridge conditions.
Accidental restart preventive
function
If y ou install the b atter y cartridge w hile pulling the
s w itch trigger, the tool does not start.
T o start the tool, release the s w itch trigger, and then pull
the s w itch trigger again.
When the lock b utton is engaged, pull the s w itch trigger
full y and release it to e x it the lock. T hen pull the s w itch
trigger again.
Electronic function
T he tool is equipped w ith the follo w ing electronic func-
tion for eas y operation.
Constant speed control
Possi b le to perform a sta b le operation, b ecause the
speed (frequency) of vibrations is kept constant even
under the loaded condition.
Application
For formw ork and surface
vibrating operations;
C ommonly used in precast con-
crete construction, small pours
that require a minimal amount of
v ib ration, patching and repairing
w ork w ith precise operation.
For vibrations at larger pours;
Ideal for pours w ith a greater sur-
face area, such as construction
joints, slab consolidation, where
the operator mov es around to
cov er the entire area.
ASSEMBLY
CAUTION:
Al w ays be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any w ork on the tool.
Installing and removing flexible
shaft
Optional accessory
Installation
1. Pull the flexible core shaft reasonably straight out
of the outer casing.
Fig.16: 1. Fle x i b le core shaft 2. O uter casing
2. H old the dri v e shaft in the tool still using the
wrench provided. Then hand thread the end fitting of the
flexible core shaft onto the solid drive shaft in the tool.
Fig.17: 1. Dri v e shaft 2. End fitting 3. Fle x i b le core
shaft
3. Fasten the end fitting of the flexible core shaft up
tightl y using a pair of pliers.
Fig.18
4.
H and thread the coupling of the outer casing onto
the male thread of the tool.
Fig.19: 1. C oupling 2. O uter casing 3. Male thread
If the coupling does not reach or fit securely onto the
male thread of the tool, especiall y w hen installing a long
flexible shaft, pull the outer casing further towards the
tool while hand-turning the flexible core shaft so the
shaft top well fits into the shaft slot in the vibration head
and b ecomes full y engaged.
Fig.20: 1. O uter casing 2. Fle x i b le core shaft
5. K nock each of the three corners of triangular
coupling w ith a hammer a fe w times in random order to
secure assem b l y .
Fig.21
Uninstallation
Follo w the installation steps in re v erse order.
Installing shoulder strap
Optional accessory
WARNING:
from the tool w hile w earing portable po w er packs.
Wearing multiple harnesses and straps ma y impair
the chances to take the equipment o quickly in a
case of emergency and result in personal injury.
WARNING:
the shoulder strap for other purposes, such as
the fall prevention at high location. If the parts
for attaching the shoulder strap are used for other
purposes, e x cessi v e load ma y b reak them and cause
serious injury to the operator and person around/
underneath the operator.
11 ENGLISH
Al w ays remove the shoulder strap
Do not use the parts for attaching