Disposal And Recycling - Scheppach 5910803900 Originalbetriebsanleitung

Akku - rasentrimmer

Vorschau ausblenden

Inhalt

Seite von 69

/ 69
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

• Push the locking button (5) upwards.

• Turn the motor head through 90° in the required

direction until it latches in place(Abb.5).

• You can convert your lawn trimmer into an edge

trimmer this way and carry out vertical cutting of

the lawn.

• When edge trimming, use the device's two guide

wheels (Fig. 6/Pos. 6+10).

• To convert the equipment back to its original state,

proceed in reverse order.

Extending the cutting thread

Warning! Do not use metal wire or plastic-coated

metal wire of any kind in the spool. This can lead to

severe injuries to the user.

To extent the cutting thread, keep the device run-

ning and tap the spool on the ground. The thread will

be extended automatically. The blade on the safety

screen shortens the thread to the approved length.

Replacing the cutting thread (Fig. 7-9)

• Hold on to the casing (f) and, at the same time,

turn the lid (g) anti-clockwise and remove it.

• Remove the casing spool (h) and spring.

• Replace the thread (i), insert the spool (h) and

spring, and, at the same time, pull the thread

through the opening. Replace the lid (g) by turn-

ing it clockwise and holding on to the casing

Sharpening the cutting blade (Fig. 6)

• Loosen the cutting blade's (l) cross-head screws

(k) from the protective hood (7).

• Put the cutting blade (l) into a vice.

• Using a flat file, sharpen the edge of the cutting

blade (l)

• Make sure that the original cutting angle is main-

tained.

• Fix the cutting blade (l) back onto the protective

hood (7).

Cleaning and maintenance

Before putting away or cleaning the grass trimmer,

switch off and remove the battery pack.

Cleaning

• Regularly check the device before starting work

• Damaged parts have to be repaired or replaced by

an authorised service department before you can

work with the device

• Only ever use original accessories and spare

parts.

• Use the device only with batteries and chargers

intended for it.

• Do not use the charger if it is damaged.

• Using other components can lead to fire.

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it

down with compressed air at low pressure.

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

• We recommend that you clean the equipment im-

mediately after you use it.

• Clean the equipment regularly with a damp cloth

and some soft soap. Do not use cleaning agents

or solvents; these may be aggressive to the plastic

parts in the equipment. Ensure that no water can

get into the interior of the equipment. The ingress

of water into an electric tool increases the risk of

an electric shock.

• Use a brush to remove deposits from the safety

guard.

Maintenance

There are no other parts inside the equipment which

require maintenance.

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the fol-

lowing parts are therefore also required for use as

consumables.

Wear parts*: thread

* Not necessarily included in the scope of delivery!

Storage

(f).

NOTE

• Store the device in a dry and frost-free (10-25 °C)

place.

• Store the battery and the device separately from

each other.

• Charge the battery before storing it for the winter.

• Keep the device, and its plastic components in par-

ticular, away from brake fluid, petrol, products con-

taining oil, penetrating oil etc. They contain chemi-

cal substances that may damage or destroy the

plastic parts of the device.

• Fertilisers and other garden chemicals contain

substances which can have a heavily corrosive

effect on metal parts. Do not store the device close

to these substances.